The aim of this study is to generate operational data that can be used to improve the production capacity in the Fluid Catalytic Cracking Unit (FCCU) in a Refinery and Petrochemical Company. This will aid in tackling the daunting challenge of unavailability of operational data that can be used to better understand and improve production capacity and ensure maximizing catalyst utilization. In addition, it addresses the challenges of analysis and control of the FCCU process due to its very complicated and little-known hydrodynamics, complex kinetics of both reactions of cracking and coke burning, strong interaction between the reactor and regenerator, and numerous operating constraints. Aspen HYSYS version 8.0 was used in modeling the cracking process using parameters extracted from the operating manual of the FCCU in the refinery. The operational data was used to compare the simulated effect of stepwise input in feed and reactor plenum temperatures as well as stepwise increase in reactor length on yield, cata lyst-to-oil-ratio and catalyst regeneration. An optimum flow in naphtha was obtained by the interaction of the inlet crude flow rate, riser height, and temperature this optimum was supported by the study of the interaction of these parameters when, catalyst to oil ratio was set as the dependent parameter. The inferences drawn from the results are that the reactor plenum temperature of 560 ℃ and a riser length of 27 m are recommended for optimum performance that ensure s lasting effect of an efficient catalyst activity.
Wilczura-Wachnic, H. (1973) Catalytic Cracking of Hydrocarbons. Chemical Technology Division, Faculty of Chemistry, University of Warsaw, Warsaw, 7-9.
Martínez, V. and Shadman, F. (2020) Improving the Performance of Fixed-Bed Catalytic Reactors by Innovative Catalyst Distribution. Journal of Applied Mathematics and Physics, 8, 672-683. https://doi.org/10.4236/jamp.2020.84052
Hadi, G. and Hadi, A. (2022) Kinetic Study of Methanol Dehydration to Dimethyl Ether in Catalytic Packed Bed Reactor over Resin. Journal of Materials Science and Chemical Engineering, 10, 45-58. https://doi.org/10.4236/msce.2022.106005
Olugbenga, A.G., Olujinmi, J.O., Yahya, M.D. and Garba, M.U. (2018) Simulation and Unit Cost of Using Fluid Catalytic Cracking of Soyabeans Oil for the Production of Bio-Gasoline. Covenant Journal of Entrepreneurship, 2, 27-33. https://journals.covenantuniversity.edu.ng/index.php/cjoe/article/view/1170
Ramasubramanian, S. (2001) Optimization of a Model IV Fluidized Catalytic Cracking Unit.
Raji, O.Y., El-Nafaty, U.A. and Jibril, M. (2012) Effect of Operational Variables on Riser Reactor of FCCU Using Hysys. A Proceeding of International Journal of Computer Application, 3, 1-8.
Ibsen, K. (2006) Equipment Design and Cost Estimation for Small Modular Biomass Systems, Synthesis Gas Clean Up, and Oxygen Separation Equipment. NREL Technical Monitor, San Francisco, 1-12.
Gómez-Velásquez, N., López-Montoya, T., Bustamante-Chaverra, C.A. and Nieto-Londoño, C. (2021) Parametric Study of Particles Homogenization in Cold-Flow Riser Reactors. International Journal of Thermofluids, 9, Article ID: 100058. https://doi.org/10.1016/j.ijft.2020.100058
Lopez-Isunza, F. (1992) Dynamic Modelling of an Industrial Fluid Catalytic Cracking Unit. Computers & Chemical Engineering, 16, S139-S148. https://doi.org/10.1016/S0098-1354(09)80016-1
Rajeev, N., Prasad, R.K. and Ragula, U.R. (2015) Process Simulation and Modeling of Fluidized Catalytic Cracker Performance in Crude Refinery. Petroleum Science and Technology, 33, 110-117. https://doi.org/10.1080/10916466.2014.953684
Fals, J., Garcia, J. R., Falco, M. and Sedran, U. (2020) Performance of Equilibrium FCC Catalysts in the Conversion of the SARA Fractions in VGO. Energy & Fuels, 34, 16512-16521. https://doi.org/10.1021/acs.energyfuels.0c02804
Heydari, M., AleEbrahim, H. and Dabir, B. (2010) Study of Seven-Lump Kinetic Model in the Fluid Catalytic Cracking Unit. The American Journal of Applied Sciences, 7, 71-76. https://doi.org/10.3844/ajassp.2010.71.76
Kassel, L.S. (1948) Prevention of Afterburning in Fluidized Catalytic Cracking Processes. U.S. Patent 2,436,927A.
Oloruntoba, A., Zhang, Y. and Hsu, C.S. (2022) State-of-the-Art Review of Fluid Catalytic Cracking (FCC) Catalyst Regeneration Intensification Technologies. Energies, 15, 2061. https://doi.org/10.3390/en15062061
Blaser, P., Pendergrass, J., Gabites, J. and Brooke, A. (2018) Viva Energy’s Geelong Refinery Reduces FCCU Turnaround Risk. Hydrocarbon Processing, 1-6. https://www.hydrocarbonprocessing.com/magazine/2018/september-2018/special-focus-refining-technology/viva-energy-s-geelong-refinery-reduces-fccu-turnaround-risk
Arbel, A., Huang, Z., Rinard, I.H., Shinnar, R. and Sapre, A.V. (1995) Dynamic and Control of Fluidized Catalytic Crackers. 1. Modeling of the Current Generation of FCC’s. Industrial & Engineering Chemistry Research, 34, 1228-1243. https://doi.org/10.1021/ie00043a027
Wu, D., Schmidt, M., Huang, X. and Verplaetsen, F. (2017) Self-Ignition and Smoldering Characteristics of Coal Dust Accumulations in O2/N2 and O2/CO2 Atmospheres. Proceedings of the Combustion Institute, 36, 3195-3202. https://doi.org/10.1016/j.proci.2016.08.024
Oloruntoba, A., Zhang, Y. and Xiao, H. (2022) Study on Effect of Gas Distributor in Fluidized Bed Reactors by Hydrodynamics-Reaction-Coupled Simulations. Chemical Engineering Research and Design, 177, 431-447. https://doi.org/10.1016/j.cherd.2021.10.031
Olugbenga, A.G., Al-Mhanna, N.M., Yahya, M.D., Afolabi, E.A. and Ola, M.K. (2021) Validation of the Molar Flow Rates of Oil and Gas in Three-Phase Separators Using Aspen Hysys. Processes, 9, 327. https://www.mdpi.com/2227-9717/9/2/327 https://doi.org/10.3390/pr9020327
Vogt, E.T. and Weckhuysen, B.M. (2015) Fluid Catalytic Cracking: Recent Developments on the Grand Old Lady of Zeolite Catalysis. Chemical Society Reviews, 44, 7342-7370. https://doi.org/10.1039/C5CS00376H
Aspen Technology Inc. (2011) Aspen HYSYS ® Dynamics V7.3. https://www.aspentech.com
Idris, M.N., Mahmud, T. and Gibbs, B. (2007) Hydrodynamics Design of a Robust Fluid Catalytic Cracking (FCC) Riser Reactor Model. Petroleum Training Journal, 4.
Ikeda, S. and Ino, T. (1999) Down-Flow FCC Pilot Plant for Light Olefin Production. In: Proceeding of the Symposium on Advances in Fluid Catalytic Cracking, American Chemical Society, New Orleans, 22-26.
Kaduna Refinning and Petrochemical Company (1980) Handbook for Process Operations. Chioda Chemical Engineering Company, Yokohoma.
Zhang, Y., Li, Z., Wang, Z. and Jin, Q. (2021) Optimization Study on Increasing Yield and Capacity of Fluid Catalytic Cracking (FCC) Units. Processes, 9, 1497. https://doi.org/10.3390/pr9091497
Reza, S. (2000) FCC Handbook, Design, Operation and Trouble Shooting of FCC facilities. 2nd Edition, Gulf Professional Publishers, Houston, 1-39, 40, 45, 52.
Tungler, A. (2012) Catalytic Technologies of the Oil Industry. HAS CER.
Becerril, E.L., Yescas, R.M. and Sotelo, D.S. (2004) Effect of Modeling Pressure Gradient in the Simulation of Industrial FCC Risers. Chemical Engineering Journal, 100, 181-186. https://doi.org/10.1016/j.cej.2004.03.001
Philip, K., Niccum, M. and Chris, R. (2002) Handbook of Petroleum Refining Process. McGraw-Hill, New York, 3.0-3.33.