Robustness and Accuracy Test of Particular Matter Prediction Based on Neural Networks
- 1 School of Mechanical and Automotive Eng., Kingston University London, UK SW15 3DW
- 2 School of Automotive Engineering, Wuhan University of Technology, Wuhan 430070, China
- 3 School of Mechanical and Automotive Eng., Kingston University London, UK SW15 3DW
Abstract
The increasingly stringent emissions regulations require that engine manufacturers must reduce emissions of particulate matter (PM). PM is made up mainly of carbon in the form of PM and complex compound that are absorbed into the PM particles. Significant quantities PM poses a threat to health. Technologies available for PM reduction are heavily dependent on after-treatment systems, which are respectively active and passive. An active trap system requires a control unit to trigger and control the regeneration process (clean the trap system). The measurement of PM is crucial for the trap system to enable the fine judgment as to when to initiate the process. If the regeneration is too infrequent, the filter will block. The frequency of the regeneration and the life of the filter are compromised. Diesel engine particular matter prediction has always been a major challenge to the industry. A simple way to handle the PM estimation is to use black-box modelling as described in [J. Deng, B. Maass, R. Stobart, PM prediction in both steady state and transient operation of diesel engines, Proc IMechE, Part D: Journal of Automobile Engineering, 2011, 225, in press, DOI: 10.1177/0954407011418029]. This method is used to estimate the PM successfully in both steady and transient engine operation condition. The main question is how robust and accurate the neural networks are for a regeneration trigger signal of diesel particular filters. In order to answer such a question, the robust test of PM estimation is carried out based on different composition of bio-diesel. In this paper, regular diesel fuel will be blended with up to 20% bio-diesel to test the effect of different fuel resources on particulate matter. Bio-diesel is often added to regular diesel fuel to improve the burning properties and reduce carbon emissions, also is alternative source of fuels. The aim of this paper with these tests is to ensure that with a realistic change in the fuel composition the estimation of PM is still accurate. Therefore, neural networks could be used to produce a regeneration signal for diesel particular filter. In this paper a virtual sensor is proposed to measure the PM. The purpose of the proposed virtual sensor is to estimate the accumulation of PM and to trigger a regeneration cycle. The virtual sensor based on neural network is used to estimate the PM. In this paper, the performance, robustness and accuracy of simulated the sensor are evaluated in measuring the particulate amount for non-road transient cycle tests.
- A. P. E. York, M. Ahmadinejad, T. C. Watling, A. P. Walker, J. P. Cox, J. Gast, P. G. Blakeman and R. Allansson, “Modeling of the Catalyzed Continuously Regenerating DPF (CCR-DPF) System: Model Development and Passive Regeneration Studies,” SAE 2007- 01-0043.
- Allansson, R. Cooper, J. Barry, J. E. Thoss, A. Uusimäki, A. P. Walker and J. P. Warren, “European Experience of High Mileage Durability of Continuously Regenerating Diesel Particulate Filter Technology,” SAE 2000- 01-0480.
- R. Allansson, P. G. Blakeman, B. J. Cooper, H. Hess, P. J. Silcock and A. P. Walker, “Optimising the Low Temperature Performance and Regeneration Efficiency of the Continuously Regenerating Diesel Particulate Filter (CR-DPF) System,” SAE 2002-01-0428.
- R. Zhan, Y. Huang and M. Khair, “Methodologies to Control DPF Uncontrolled Regenerations,” SAE 2006-01-1090.
- M. P. Sturgess, S. F. Benjamin and C. A. Roberts, “Spatial Conversion Profiles within an SCR in a Test Exhaust System with Injection of Ammonia Gas Modelled in CFD Using the Porous Medium Approach,” SAE 2010-01-2126.
- Y. Liu, “Diesel Engine Modelling and Optimization for Emission Reduction,” PhD Thesis, University of Wisconsin-Madison, 2005.
- I. M. Kennedy, “Models of PM Formation and Oxidation,” Progress in Energy and Combustion Science, Vol. 23, No. 2, 1997, pp. 95-132. doi:10.1016/S0360-1285(97)00007-5
- H. P. M. Bockhorn, “Formation in Combustion: Mechanism and Models,” Springer-verlag, Heidelberg, Vol. 59, 1994. doi:10.1007/978-3-642-85167-4
- A. Westlund, “Measuring and Predicting Transient Diesel Engine Emissions,” Academic Thesis, Royal Institute of Technology, Stockholm, 2009.
- B. Wu, R. G. Prucka, Z. S. Filipi, D. M. Kramer and G. L. Ohl, “Cam-Phasing Optimization Using Artificial Neural Networks as Surrogate Models—Fuel Consumption and NOx Emissions,” SAE 2006-01-1512.
- Y. He and C. J. Rutland, “Application of Artificial Neural Networks in Engine Modeling,” International Journal of Engine Research, 2004, Vol. 5, No. 4, pp. 281-296. doi:10.1243/146808704323224204
- B. Maass, R. Stobart and J. Deng, “Diesel Engine Emissions Prediction with Parallel Neural Networks,” American Control Conference, 2009.
- N. Bose and N. S. Kumar, “Prediction of Engine Emissions through Fuzzy Logic Modelling,” Interna-tional Conference on Computational Intelligence and Multimedia Applications, 2007.