An Experimental Simulation of a Design Three-Port DC-DC Converter
- 1 Electrical Engineering Department, Taibah University, Madinah, KSA
- 2 Energy Engineering Department, German Jordanian University, Amman, Jordan
- 3 Electrical Engineering and Computer Science Department, University of Central Florida, Orlando, USA
- 4 Electrical Engineering and Computer Science Department, University of Central Florida, Orlando, USA
Abstract
Traditional DC-DC converter topologies interface two power terminals: a source and a load. The construction of diverse and flexible power management and distribution (PMAD) systems with such topologies is governed by a tight compromise between converter count, efficiency, and control complexity. The broader impact of the current research activity is the development of enhanced power converter systems suitable for a wide range of applications. Potential users of this technology include the designers of portable and stand-alone systems such as laptops, hand-held electronics, and communication repeater stations. High power topology options support the evolution of clean power technologies such as hybrid-electric vehicles (HEV’s) and solar vehicles. DC-DC converter is considered as an advanced environmental issue since it is a greenhouse emission eliminator. By utilizing the advancement of these renewable energy sources, we minimize the use of fossil fuel. Thus, we will have a cleaner and pollution free environment. In this paper, a three-port DC-DC converter is designed and discussed. The converter was built and tested at the energy research laboratory at Taibah University, Al Madinah, KSA.
- Capel, A. (1998) The Power System of the Multimedia Constellation Satellite for the Skybridge Missions. Proceedings of IEEE Power Electronics Specialist Conference, 1913-1930.
- Brandhorst, H.W., O’Neill, M.J. and Eskenazi, M. (2003) Photovoltaic Options for Increased Satellite Power at Lower Cost. Proceedings of IEEE Photovoltaic Energy Conversion, 849-852.
- Jang, S. and Choi, J. (2008) Energy Balance Analysis of Small Satellite in Low Earth Orbit (LEO). Proceedings of IEEE Power and Energy Conference, 967-971.
- Middlebrook, R.D. and Cuk, S. (1977) A General Unified Approach to Modeling Switching-Converter Power Stages. International Journal of Electronics, 42, 521-550. http://dx.doi.org/10.1080/00207217708900678
- Cuk, S. (1976) Modeling, Analysis, and Design of Switching Converters. Ph.D. Thesis, California Institute of Technology, Pasadena.
- Di Napoli, A., Crescimbini, F., Solero, L., Caricchi, F. and Capponi, F.G. (2002) Multiple-Input DC-DC Power Con- verter for Power-Flow Management in Hybrid Vehicles. Proceedings of IEEE Industry Application Conference, 1578- 1585.
- Jiang, W. and Fahimi, B. (2009) Multi-Port Power Electric Interface for Renewable Energy Sources. IEEE 2009 Applied Power Electronics Conference, 347-352.
- Imes, W.G. and Rodriguez, F.D. (1994) A Two-Input Tri-State Converter for Spacecraft Power Conditioning. Pro- ceedings of AIAA International Energy Conversion Engineering Conference, 163-168.
- Rodriguez, F.D. and Imes, W.G. (1994) Analysis and Modeling of a Two-Input DC/DC Converter with Two Con- trolled Variables and Four Switched Networks. Proceedings of AIAA International Energy Conversion Engineering Conference, 322-327.
- Dobbs, B.G. and Chapman, P.L. (2003) A Multiple-Input DC-DC Converter Topology. IEEE Power Electronics Let- ters, 1, 6-9.
- Benavides, N.D. and Chapman, P.L. (2005) Power Budgeting of a Multiple-Input Buck-Boost Converter. IEEE Transactions on Power Electronics, 20, 1303-1309. http://dx.doi.org/10.1109/TPEL.2005.857531
- Matsuo, H., Lin, W.Z., Kurokawa, F., Shigemizu, T. and Watanabe, N. (2004) Characteristics of the Multiple-Input DC-DC Converter. IEEE Transactions on Industrial Electronics, 51, 625-631.
- Solero, L., Caricchi, F., Crescimbini, F., Honorati, O. and Mezzetti, F. (1996) Performance of a 10 kW Power Electronic Interface for Combined Wind/PV Isolated Generating Systems. Annual IEEE Power Electronics Specialists Conference, 2, 1027-1032.