Research ArticleOpen AccessGoogle Scholar indexed
Analysis of the Tool Condition Monitoring System Using Fuzzy Logic and Signal Processing
Department of Mechanical Engineering, Anna University Regional Campus, Madurai, India
V V College of Engineering, Tisayanvilai, India
- 1 Department of Mechanical Engineering, Anna University Regional Campus, Madurai, India
- 2 V V College of Engineering, Tisayanvilai, India
Circuits and Systems·Volume 07 (2016)·Pages 2689–2701·Published 5 July 2016·DOI10.4236/cs.2016.79232
Copy link · social · email
Abstract
In the present investigation, an attempt was made to facilitate tool condition monitoring system on cryogenic treated using fuzzy logic and signal processing. Cryogenic treatment is carried out at -196 ° C for 48 hours followed on tempering at 200 ° C for 2 hours. The AISI4340 steel is machined with cryogenically treated inserts. Speed, feed and depth of cut are selected as input parameters. The results of the proposed method are encouraged in minimizing tool vibration, flank and crater wear. Good correlation is shown between the neural fuzzy and experimental data. As a result, it is found that cryogenically treated inserts have superior tool wear and vibration resistance, and confirmed by conducting further confirmation tests.
KeywordsVibrationCryogenic TemperatureTool WearFuzzy Logic
- Liu, K., Li, X., Rahman, M. and Liu, X. (2003) CBN Tool Wear in Ductile Cutting of Tungsten Carbide. Wear, 255, 1344-1351. http://dx.doi.org/10.1016/S0043-1648(03)00061-9
- Dossett, J. and Totten, G. (2013) Cold and Cryogenic Treatment of Steel. ASM Hand Book, Steel Heat Treating Fundamentals and Process, Vol. 4, 382-386
- Bhateja, A., Bhardwaj, J., Singh, M. and Pal, S.K. (2013) Optimization of Different Performance Parameters i.e. Surface Roughness, Tool Wear Rate & Material Removal Rate with the Selection of Various Process Parameters Such as Speed Rate, Feed Rate, Specimen Wear, Depth of Cut in CNC Turning of EN24 Alloy Steel—An Empirical Approach. The International Journal of Engineering and Science, 2, 103-113.
- Jeon, J. and Kim, S. (1988) Optical Flank Wear Monitoring of Cutting Tools by Image Processing. Wear, 127, 207- 217. http://dx.doi.org/10.1016/0043-1648(88)90131-7
- Chou, Y.K. and Evans, C.J. (1997) Tool Wear Mechanism in Continuous Cutting of Hardened Tool Steels. Wear, 212, 59-65. http://dx.doi.org/10.1016/S0043-1648(97)00139-7
- Panigrahi, S.K. and Jayaganthan, R. (2011) Effect of Annealing on Thermal Stability, Precipitate Evolution, and Mechanical Properties of Cryorolled Al 7075 Alloy. Metallurgical and Materials Transactions A, 42, 3208-3217. http://dx.doi.org/10.1007/s11661-011-0723-y
- Singh, H. and Kumar, P. (2004) Tool Wear Optimization in Turning Operation by Taguchi Method. Indian Journal of Engineering and Materials Sciences, 11, 19-24.
- Davim, J.P. and Figueira, L. (2007) Machinability Evaluation in Hard Turning of Cold Work Tool Steel (D2) with Ceramic Tools Using Statistical Techniques. Materials & Design, 28, 1186-1191. http://dx.doi.org/10.1016/j.matdes.2006.01.011
- Luo, S., Liao, Y. and Tsai, Y. (1999) Wear Characteristics in Turning High Hardness Alloy Steel by Ceramic and CBN Tools. Journal of Materials Processing Technology, 88, 114-121. http://dx.doi.org/10.1016/S0924-0136(98)00376-8
- Gill, S.S., Singh, R., Singh, H. and Singh, J. (2009) Wear Behaviour of Cryogenically Treated Tungsten Carbide Inserts under Dry and Wet Turning Conditions. International Journal of Machine Tools and Manufacture, 49, 256-260. http://dx.doi.org/10.1016/j.ijmachtools.2008.11.001
- Thamizhmanii, S. and Hasan, S. (2006) Analyses of Roughness, Forces and Wear in Turning Gray Cast Iron. Journal of Achievements in Materials and Manufacturing Engineering, 17, 401-404.