Numerical Optimization by Finite Element Method of Stainless Steel/Glass-Epoxy Composite Bolted Joint under Tension and Compression
- 1 National Engineering School of Metz, University of Lorraine, Metz, France
- 2 National Engineering School of Metz, University of Lorraine, Metz, France
- 3 National Engineering School of Metz, University of Lorraine, Metz, France
- 4 National Engineering School of Metz, University of Lorraine, Metz, France
Abstract
The aim of this study was to optimize the geometry and the design of metallic/composite single bolted joints subjected to tension-compression loading. For this purpose, it was necessary to evaluate the stress state in each component of the bolted join. The multi-material assembly was based on the principle of double lap bolted joint. It was composed of a symmetrical balanced woven glass-epoxy composite material plate fastened to two stainless sheets using a stainless pre-stressed bolt. In order to optimize the design and the geometry of the assembly, ten configurations were proposed and studied: a classical simple bolted joint, two joints with an insert (a BigHead<sup>R</sup> insert and a stair one) embedded in the composite, two “waved” solutions, three symmetrical configurations composed of a succession of metallic and composites layers, without a sleeve, with one and with two sleeves, and two non-symmetrical constituted of metallic and composites layers associated with a stair-insert (one with a sleeve and one without). A tridimensional Finite Element Method (FEM) was used to model each configuration mentioned above. The FE models taked into account the different materials, the effects of contact between the different sheets of the assembly and the pre-stress in the bolt. The stress state was analyzed in the composite part. The concept of stress concentration factor was used in order to evaluate the stress increase in the highly stressed regions and to compare the ten configurations studied. For this purpose, three stress concentration factors were defined: one for a monotonic loading in tension, another for a monotonic loading in compression, and the third for a tension-compression cyclic loading. The results of the FEM computations showed that the use of alternative metallic and composite layers associated with two sleeves gived low values of stress concentration factors, smaller than 1.4. In this case, there was no contact between the bolt and the composite part and the most stressed region was not the vicinity of the hole but the end of the longest layers of the metallic inserts.
- Lim, G.-H., Bodjona, K., Raju, K.P., et al . (2018) Evolution of Mechanical Properties of Flexible Epoxy Adhesives under Cyclic Loading and Its Effects on Composite Hybrid Bolted/Bonded Joint Design. Composite Structures , 189, 54-60. https://doi.org/10.1016/j.compstruct.2018.01.049
- Lopez-Cruz, P., Laliberté, J. and Lessard, L. (2017) Investigation of Bolted/Bonded Composite Joint Behaviour Using Design of Experiments. Composite Structures , 170, 192-201. https://doi.org/10.1016/j.compstruct.2017.02.084
- Khashaba, U.A. (2018) Static and Fatigue Analysis of Bolted/Bonded Joints Modified with CNTs in CFRP Composites under Hot, Cold and Room Temperatures. Composite Structures , 194, 279-291. https://doi.org/10.1016/j.compstruct.2018.04.008
- Marannano, G. and Zuccarello, B. (2015) Numerical Experimental Analysis of Hybrid Double Lap Aluminum-CFRP Joints. Composites Part B : Engineering , 71, 28-39. https://doi.org/10.1016/j.compositesb.2014.11.025
- Liu, F.R., Lu, X.H., Zhao, L.B., Zhang, J.Y., Xu, J.F. and Hu, N. (2018) Investigation of Bolt Load Redistribution and Its Effect on Failure Prediction in Double-Lap, Multi-Bolt Composite Joints. Composite Structures , 202, 397-405. https://doi.org/10.1016/j.compstruct.2018.02.043
- Mandal, B. and Chakrabarti, A. (2018) Numerical Failure Assessment of Multi-Bolt FRP Composite Joints with Varying Sizes and Preloads of Bolts. Composite Stru c tures , 187, 169-178. https://doi.org/10.1016/j.compstruct.2017.12.048
- Nerilli, F. and Vairo, G. (2017) Progressive Damage in Composite Bolted Joints via a Computational Micromechanical Approach. Composites Part B : Engineering , 111, 357-371. https://doi.org/10.1016/j.compositesb.2016.11.056
- Hua, X.F., Haris, A., Ridha, M., Tan, V.B.C. and Tay, T.E. (2018) Progressive Failure of Bolted Single-Lap Joints of Woven Fiber-Reinforced Composites. Composite Structures , 189, 443-454. https://doi.org/10.1016/j.compstruct.2018.01.104
- Khashaba, U.A., Sallam, H.E.M., Al-Shorbagy, A.E. and Seif, M.A. (2006) Effect of Washer Size and Tightening Torque on the Performance of Bolted Joints in Composite Structures. Composite Structures , 73, 310-317. https://doi.org/10.1016/j.compstruct.2005.02.004
- Choia, J., Hashemini, S.M., Chun, H.-J., Park, J.-C. and Chang, H.S. (2018) Failure Load Prediction of Composite Bolted Joint with Clamping Force. Composite Stru c tures , 189, 247-255. https://doi.org/10.1016/j.compstruct.2018.01.037