Research ArticleOpen AccessGoogle Scholar indexed
Numerical Study of Flow and Thermal Field on a Parallel Flow Vortex Tube
Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
- 1 Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
- 2 Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
- 3 Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
- 4 Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
- 5 Department of Mechanical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
Copy link · social · email
Abstract
Flow and thermal field of a parallel flow vortex tube has been simulated and analyzed numerically. A secondary zone model is found at the core region near the inlet to the middle of the vortex tube. Blockage effect due to a narrow area of the hot exit has deflected air flow towards the cold exit, caused expansion and compression at the cold and hot outlet, respectively. The cooling and heating effect due to energy separation is contributed by expansion and compression of air near the outlet. Coeficient of performance (COP) for a refrigerator is higher as cold mass fraction increases due to a higher temperature difference and cold mass flow rate.
KeywordsParallel Flow Vortex TubeEnergy SeparationExpansionCompressionSecondary FlowCOP
- G. J. Ranque, “Experiments on Expansion in a Vortex with Simultaneous Exhaust of Hot and Cold Air,” Le Journal De Physique et le Radium (Paris), Vol. 4, 1933, pp. 112-114.
- R. Hilsch, “The Use of the Expansion of Aires in Centrifugal Field as a Cooling Process,” Review of Scientific Instrument, Vol. 18, No. 2, 1947, pp. 108-113. doi:10.1063/1.1740893
- B. Ahlborn and S. Groves, “Secondary Flow in a Vortex Tube,” Fluid Dynamics Research, Vol. 21, No. 2, 1997, pp. 73-86. doi:10.1016/S0169-5983(97)00003-8
- S. U. Nimbalkar and M. R. Muller, “An Experimental Investigation of the Optimum Geometry for the Cold End Orifice of a Vortex Tube,” Applied Thermal Engineering, Vol. 29, 2009, pp. 509-514. doi:10.1016/j.applthermaleng.2008.03.032
- Y. Xue and M. Arjomandi, “The Effect of Vortex Angle on the Efficiency of the Ranque-Hilsch Vortex Tube,” Experimental Thermal and Fluid Science, Vol. 33, No. 1, 2008, pp. 54-57. doi:10.1016/j.expthermflusci.2008.07.001
- T. Farouk and B. Farouk, “Large Eddy Simulations of the Flow Field and Temperature Separation in the RanqueHilsch Vortex Tube,” International Journal of Heat and Mass Transfer, Vol. 50, 2007, pp. 4724-4735. doi:10.1016/j.ijheatmasstransfer.2007.03.048
- N. J. Wills and A. S. Karthika, “Numerical Analysis of Flow Behaviour and Energy Separation in Vortex Tube,” 10th National Conference on Technological Trends (NCTT 09), 6-7 November 2009, pp. 130-135.
- N. Pourmahmoud, A. H. Zadeh, O. Moutaby and A. Bramo, “Computational Fluid Dynamic Analysis of Helical Nozzles Effects on the Energy Separation in a Vortex Tube,” Thermal Science, Vol. 16, No. 1, 2012, pp. 151-166. doi:10.2298/TSCI110531085P