Modelling and Optimisation of a Spring-Supported Diaphragm Capacitive MEMS Microphone
- 1
- 2
- 3
Abstract
Audio applications such as mobile communication and hearing aid devices demand a small size but high performance, stable and low cost microphone to reproduce a high quality sound. Capacitive microphone can be designed to fulfill such requirements with some trade-offs between sensitivity, operating frequency range, and noise level mainly due to the effect of device structure dimensions and viscous damping. Smaller microphone size and air gap will gradually decrease its sensitivity and increase the viscous damping. The aim of this research was to develop a mathematical model of a spring-supported diaphragm capacitive MEMS microphone as well as an approach to optimize a microphone’s performance. Because of the complex shapes in this latest type of diaphragm design trend, analytical modelling has not been previously attempted. A novel diaphragm design is proposed that offers increased mechanical sensitivity of a capacitive microphone by reducing its diaphragm stiffness. A lumped element model of the spring-supported diaphragm microphone is developed to analyze the complex relations between the microphone performance factors and to find the optimum dimensions based on the design requirements. It is shown analytically that the spring dimensions of the spring-supported diaphragm do not have large effects on the microphone performance com pared to the diaphragm and backplate size, diaphragm thickness, and air-gap distance. A 1 mm2 spring-supported diaphragm microphone is designed using several optimized performance parameters to give a –3 dB operating bandwidth of 10.2 kHz, a sensitivity of 4.67 mV/Pa (–46.5 dB ref. 1 V/Pa at 1 kHz using a bias voltage of 3 V), a pull-in voltage of 13 V, and a thermal noise of –22 dBA SPL.
- C. P. R. Scheeper, A. G. H. Van Der Donk, W. Olthuis and P. Bergveld, “Review of silicon microphones,” Sensors and Actu-ators, A: Physical, Vol. 44, No. 1, 1994, pp. 1-11.
- P. Rombach, M. Mullenborn, U. Klein and K. Rasmussen, “The First Low Voltage, Low Noise Differential Silicon Microphone, Technology Development and Measurement Results,” Sensors and Actuators, A: Physical, Vol. 95, No. 2-3, 2002, pp. 196-201.
- P. R. Scheeper, W. Olthuis and P. Bergveld, “Silicon Condenser Microphone with a Silicon Nitride Diaph-ragm and Backplate,” Journal of Micromechanics and Micro-engineering, Vol. 2, No. 3, 1992, pp. 187-189.
- A. Tork-keli, O. Rusanen, J. Saarilahti, H. Seppa, H. Sipola and J. Hie-tanen, “Capacitive Microphone with Low- Stress Polysilicon Membrane and High-Stress Polysilicon Backplate,” Sensors and Actuators, A: Physical, Vol. 85, No. 1-3, 2000, pp. 116-123.
- M. Pedersen, R. Schellin, W. Olthuis and P. Bergveld, “Electroacoustical Measurements of Silicon Micro-phones on Wafer Scale,” Journal of the Acoustical Society of America, Vol. 101, No. 4, 1997, pp. 2122-2128.
- B. A. Ganji and B. Y. Majlis, “Design and Fabrication of a New MEMS Capacitive Microphone Using a Perforated Aluminum Diaphragm,” Sensors and Actuators, A: Physical, Vol. 149, No. 1, 2009, pp. 29-37.
- P. R. Scheeper, W. Olthuis and P. Bergveld, “Design, Fabrication, and Testing of Corrugated Silicon Nitride Diaphragms,” Journal of Microelectromechan-ical Systems, Vol. 3, No. 1, 1994, pp. 36-42.
- X. Li, R. Lin, H. Kek, J. Miao and Q. Zou, “Sensitivity-Improved Silicon Condenser Microphone with a Novel Single Deeply Corrugated Diaphragm,” Sensors and Actuators, A: Physical, Vol. 92, No. 1-3, 2001, pp. 257-262.
- M. Fuldner, A. Dehe and R. Lerch, “Analytical Analysis and Finite Element Simulation of Advanced Membranes for Silicon Microphones,” IEEE Sensors Journal, Vol. 5, No. 5, 2005, pp. 857-862.
- B. A. Ganji and B. Y. Majlis, “Design and Fabrication of a Novel Sin-gle-Chip MEMS Capacitive Microphone Using Slotted Diaph-ragm,” Journal of Micro/Nanolitho- graphy, MEMS, and MOEMS, Vol. 8, No. 2, 2009.
- H. J. Kim, S. Q. Lee and K. H. Park, “A Novel Capacitive Type Miniature Microphone with a Flexure Hinge Diaphragm,” Proceedings of SPIE—The International Society for Optical Engineering, Vol. 6374, Boston, 2006.
- N. Mohamad, P. Iovenitti and T. Vinay, “High sensitivity capacitive MEMS microphone with spring supported diaphragm,” Proceedings of SPIE—The International Society for Optical Engineering, SPIE, Canberra, Australia, 2008, pp. 68001T-1 until 68001T-9.