Optimization of Surface Milling of Hardened AISI4340 Steel with Minimal Fluid Application Using a High Velocity Narrow Pulsing Jet of Cutting Fluid
- 1
- 2
- 3
Abstract
Surface milling of hardened steel is carried out with copious supply of cutting fluid and is obviously associated with problems related to procurement and storage of cutting fluid. The disposal of cutting fluid has to comply with environmental legislation such as OSHA regulations. The present investigation proposes an environment friendly minimal pulsed jet cutting fluid application scheme for surface milling of AISI4340 steel with a hardness of 45 HRC using commercially available carbide tools. This scheme can be implemented as such on the shop floor with out the need for any major alternations on the existing facilities and it was observed that the new scheme is not only environment friendly but also provided better cutting performance when compared to conventional wet milling which requires copious supply of cutting fluid.
- [1] A. S Varadarajan, P. K. Philip and B. Ramamoorthy, “Investigations on Hard Turning with Minimal Cutting Fluid Application(HTMF) and Its Comparison with Dry and Wet Turning,” International Journal of Machine Tool and Manufacture, Vol. 42, No. 2, 2001, pp. 193-200.
- A. S. Varadarajan, P. K. Philip and B. Ramamoorthy, “Neural Network Assisted Performance Prediction in Hard Turning with Minimal Quantities of Cooling Lubricants,” Proceedings of the 14th International Conference, CAD/CAM, Robotics and Factories of the Future, PSG College of Technology, Coimbatore, India, 1998, pp. 654 -658.
- A. S. Varadarajan, P. K. Philip and B. Ramamoorthy, “Investigations on Hard Turning with Minimal Pulsed jet of Cutting Fluid,” Proceedings of the International Seminar on Manufacturing Technology beyond 2000, Bangalore, India, 1999, pp. 173-179.
- A. Attansio, M. Gelfi, C. Giardimi and C. Remino, “Minimal Quantity Lubrication in Turning: Effect on tool wear,” International Journal of Wear, Vol. 260, No. 3, 2006, pp. 333-338.
- A. S. Varadarajan, P. K. Philip and B. Ramamoorthy, “Optimization of Operating Parameters for the Cutting Performance during Hard Turning with Minimal Cutting Fluid,” Proceedings of the International Conference on Intelligent, Flexible, Auto-nomous Manufacturing Systems, Coimbatore, India, 2000, pp. 717-725.
- A. Raj, K. L. D. Wins, R. Gnanadurai and A. S Varadarajan, “Investigations on Hard Milling with Minimal Fluid Application,” International Confe-rence on Frontiers in Design and Manufacturing, Ka-runya University, Coimbatore, 2008, pp. 183-187.
- T. Thepsonthi, M. Hamdi and K. Mitsui, “Investigation into Minimal-Cutting Fluid Application in High-Speed Milling of Hardened Steel Using Carbide Mills,” International Journal of Machine Tools and Manufacture, Vol. 49, No. 2, 2009, pp. 156-162.
- M. Rahman, A. S. Kumar and M. U. Salam, “Experimental Evaluation on the Effect of Minimal Quantities of Lubricant in Milling,” International Journal of Machine Tools & Manufacture, Vol. 42, No. 5, 2002, pp. 539-547.
- A. S. Varadarajan, B. Ramamoorthy and P. K. Philip, “Formulation of a Cutting Fluid for Hard Turning with Minimal Fluid Application,” 20th AIMTDR conference at Birla institute of Technology Ranchi, India, 2002, pp. 89 -95.
- P. K. Philip, A. S Varadarajan and B. Ramamoorthy, “Influence of Cutting Fluid Composition and Delivery Variables on Performance in Hard Turning Using Minimal Fluid in Pulsed Jet Form,” Journal of the Institution of Engineers (India), Vol. 82, No. 3, 2001, pp. 12-19.