Utilization of Egyptian Ilmenite Ore for Steel Surface Preparation in Petroleum Field
- 1
- 2 Production Department, Egyptian Petroleum Research Institute (EPRI), Cairo, Egypt
- 3
- 4
Abstract
The construction of gas and oil plants include many items such as steel structures, equipments, piping, tanks and vessels at different conditions such as offshore, onshore, above and underground shall be protected against corrosion by coating. The protective value of a coating system is proportional to the surface preparation; the objectives of the surface preparation are the surface cleanliness and the surface profile of the substrate. The surface preparation is usually achieved by blast cleaning using different types of abrasive. Due to its high hardness and low cost, silica sand has been used extensively for impact abrasion. It is, however, very brittle with most grain disintegrating on impact, causing excessive levels of siliceous dust which is a major health hazard and causes serious environmental pollution. Consequently, it has been banned as impact abrasive material in most countries around the world. Considerable research has been done in the last twenty years to find an impact abrasive material as hard as silica and that respects. So it was important to search for sand substitution among the local abundant minerals in Egypt. Waste product obtained from ilmenite ore extracted from the mine was found to be the most suitable alternative abrasive. This work shows the abrasive types, the occurrence of the ilmenite ore. The chemical properties, physical properties and microscopic examination of the waste were investigated. The obtained result indicates that, the waste product obtained from ilmenite ore can be utilized for abrasion as sand substitution.
- R. H. Green, “Blast Cleaning—The Role of the Media.” Anti-Corrosion Methods and Materials Journal, Vol. 30, No. 6, 1983, pp. 4-6. doi:10.1108/eb007222
- Hemple Global Supplier of Paint and Coating, “Hemple Protective Coating Manual,” May 2004.
- Robinson Irwin Technical Support Ltd., “Elcometer Protective Coating Inspection Manual DOC,” No. TIME- 0147, Issue 02, 1994, pp. 5-7.
- British Stan-dard Institution (BSI), “Specification for Surface Finish of Blast-Cleaned Steel for Painting,” No. 4232, December 1967.
- American Society for Testing and Materials, “ASTM Method: C125-07, Standard Terminology Relating to Concrete and Concrete Aggregates,” 2007.
- N. R. Farrow, “Method for Removing Surface Coatings,” US Patent No. 6609955, August 26, 2003.
- Tomari Masao, Matsuda Mi-noru and Oshimia Hidetaka “Method and device for treating steel making slag”, Japanese Patent No. 590563613, 28 March 1984.
- G. L. Smith “Method and Apparatus for Stripping, Cleaning and Treating Surfaces,” US Patent No. 4044507, Au-gust 1977.
- K. Katsikaris, E. Voutsas, K. Magoulas, G. Andronikos and S. Stamataki, “Recycling Ferrous-Nickel Slag in Blast Cleaning,” Waste Management & Research on Behalf of International Solid Waste Association (ISWA), Vol. 20, No. 3, 2002, pp. 269-278.
- S. Bellermare, “Method for Blast Cleaning Using Ilmenite Tailing Particles,” US Patent No.6848973, 1 February 2005.
- United State Geological Survey (USGS), 2006.
- M. S. Amin, “The Ilmenite De-posit of Abu Ghalqa, Egypt,” Economic Geology and the Bul-letin of Society of Economic Geologists, Vol. 49, No. 1, January 1954, pp. 77-87. doi:10.2113/gsecongeo.49.1.77
- E. M. El-Shazly, “Report on the Ilmenite Ore at Abu Ghalaga Eastern Desert,” Unpublished Report, Geological Survey and Mineral Research Department, Cairo, 1959.
- E. Z. Basta and M. A. Takla, “Petrological Studies on Abu Ghalaga Ilmenite Occur-rence, Eastern Desert,” Journal of Geology, Vol. 12, No. 2, 1968, pp. 43-72.
- E. Z. Basta, “New Data on the System Fe2O3- FeTiO3-TiO2 (Ferri-Ilmenite and Titanom-agetite) ,” Proceeding Egyptian Academic Science, Cairo, Vol. 14, 1959, pp. 1-15.
- E. Z. Basta and M. A. Takla, “Mineralogy and Origin of Abu Ghalaga Ilmenite Occurrence, Eastern Desert,” Journal of Geology, Vol. 12, No. 2, 1968, pp. 87-124.