Determination of the Law of Motion of the Yarn in the Spin Intensifier
- 1 Department of Technology of Products of Textile Industry, Namangan Institute of Engineering and Technology, Namangan, Uzbekistan
- 2 Faculty of Technology of Cotton Industry, Tashkent Institute of Textile and Light Industry, Tashkent, Uzbekistan
- 3 Department of Spinning Technology, Tashkent Institute of Textile and Light Industry, Tashkent, Uzbekistan
- 4 Faculty of Engineering and Technology, Namangan Institute of Engineering and Technology, Namangan, Uzbekistan
Abstract
The article is devoted to the study of spreading of the twisted yarn in a spinning cell. The article presents the scheme and principle of operation of the effective design of the yarn-output tube of pneumomechanical spinning machine. To determine the law of motion of a roller installed in a yarn-output tube, the tension of the thread enveloping the surface of the rotating roller was studied, as a result of which the equation of its motion was obtained. As a result of solving the equation, the values of the thread tension on the surface of the rotating roller are obtained. The dependences of the change in the tension of the thread in time are obtained depending on the angle of rotation and the mass of the roller. The recommended design of the yarn-output tube allows increasing the strength characteristics of the pneumomechanical yarn.
- Astashev, M.M. (2003) Thesis for the Degree of Candidate of Technical Sciences. Improvement of Technological Operations of Feeding the Formation of Yarn on Rotor Spinning Machines. Ivanova.
- Sevostyanov, A.G. (1989) Mechanical Technology of Textile Materials. Moscow Legprombytizdat.
- Migushov, I.I. (1984) Mechanics of Textile Yarn and Fabric: Monogr. In: Mirushov, I.I., Solovyov, A.N. and Kiryukhin, S.M., Eds. Light and Food Industry, Moscow, 130s.
- Xu, B.G. and Tao, X.M. (2003) Integrated Approach to Dynamic Analysis of Yarn Twist Distribution in Rotor Spinning Part I: Steady State. Textile Research Journal, 79-89. https://doi.org/10.1177/004051750307300116
- Ba, T. and Huang, X.B. (2003) Modeling the Twist Level at the Peeling Point in Rotor Spinning. TRJ, 390-395. https://doi.org/10.1177/004051750307300504
- Guo, B.P., Tao, X.M. and Lo, T. (2000) A Mechanical Model of Yarn Twist Blockage in Rotor Spinning. TRJ, 11-17 https://doi.org/10.1177/004051750007000103
- Kiselev, R.V. (2013) Determination of the Torque Generated by the Thread Funnel When Forming the Reinforced Thread of the Pneumatic Mechanical Spinning Method. Bulletin, 1, 22-28. https://readera.ru/142184805
- Patent US 5044151, 09/03/1991 D01H 4/40.
- Korabayev, Sh.A., Djurayev, A.D. and Matismailov, S.L. (2018) Efficient Tubing Design for Spinning Yarn in a Spinning Device. TITLP, 4-5.
- Korabayev, Sh.A., Djurayev, A.D. and Matismailov, S.L. (2018) Perfection of Designs and Theoretical Bases of Calculatingroller Tubes for Yarning. International Journal of Advanced Research in Science, Engineering and Technology, IJARSET, 5, 75-83.
- Scherbakov, V.P. (2013) Applied and Structural Mechanics of Fibrous Materials. M. OOO, “Tiso Print”, 304.
- Abdukarimovich, M.O., Ibragimovich, A.K. and Sharipjanovich, S.O. (2018) Designing a New Design of a Loading Cylinder for Pneumomechanical Spinning Machines. Engineering, 10, 345-356. https://doi.org/10.4236/eng.2018.106025
- Abbazov, I., Sarimsakov, O., Khodjiev, M. and Mardonov, B. (2018) Waste Produced at Cotton Waste Factories. American Journal ASCIT Communications, 5, 22-28.