It is known from the New Energy and Industry Technology Development Organization (NEDO) roam map Japan, 2017 that the polymer electrolyte fuel cell (PEFC) power generation system is required to operate at 100°C for application of mobility usage from 2020 to 2025. This study aims to clarify the effect of separator thickness on the distribution of the temperature of reaction surface ( T react ) at the initial temperature of cell ( T ini ) with flow rate, relative humidity (RH) of supply gases as well as RH of air surrounding cell of PEFC. The distribution of T react is estimated by means of the heat transfer model considering the H 2 O vapor transfer proposed by the authors. The relationship between the standard deviation of T react - T ini and total voltage obtained in the experiment is also investigated. We can know the effect of the flow rate of supply gas as well as RH of air surrounding cell of PEFC on the distribution of T react - T ini is not significant. It is observed the wider distribution of T react - T ini provides the reduction in power generation performance irrespective of separator thickness. In the case of separator thickness of 1.0 mm, the standard deviation of T react - T ini has smaller distribution range and the total voltage shows a larger variation compared to the other cases.
KeywordsPolymer Electrolyte Fuel CellHeat Transfer ModelingH<sub>2</sub>O Vapor TransferTemperature DistributionHigh Temperature
NEDO (New Energy and Industry Technology Development Organization) (2022). https://www.nedo.go.jp/cotent/100871973.pdf
Zhang, G. and Kandlikar, S.G.A. (2012) Critical Review of Cooling Technique in Proton Exchange Membrane Fuel Cell Stacks. International Journal of Hydrogen Energy, 37, 2412-2429. https://doi.org/10.1016/j.ijhydene.2011.11.010
Mohamed, W.A.N.W., Talib, S.F.A., Zakaria, I.A., Mamat, A.M.I. and Daud, W.R.W. (2018) Effect of Dynamic Load on the Temperature Profiles and Cooling Response Time of a Proton Exchange Membrane Fuel Cell. Journal of the Energy Institute, 91, 349-357. https://doi.org/10.1016/j.joei.2017.02.006
Zhang, J., Zhang, C., Hao, D., Ni, M., Huang, S., Liu, D. and Zheng, Y. (2021) 3D Non-Isothermal Dynamic Simulation of High Temperature Proton Exchange Membrane Fuel Cell in the Start-Up Process. International Journal of Hydrogen Energy, 46, 2577-2593. https://doi.org/10.1016/j.ijhydene.2020.10.116
Zhang, J., Xie, Z., Zhang, J., Tang, Y., Song, C., Navessin, T., Shi, Z., Song, D., Wang, H., Wilikinson, D.P., Liu, Z.S. and Holdcroft, S. (2006) High Temperature PEM Fuel Cells. Journal of Power Sources, 160, 872-891. https://doi.org/10.1016/j.jpowsour.2006.05.034
Jin, C., Wang, T., Che, X., Dong, J., Liu, R. and Yang, J. (2022) New High-Performance Bulky N-Heterocyclic Group Functionalized Poly(Terphenyl Piperidinium) Membranes for HT-PEMFC Applications. Journal of Membrane Science, 641, Article ID: 119884. https://doi.org/10.1016/j.memsci.2021.119884
Budak, Y. and Devrim, Y. (2022) Micro-Cogeneration Application for a High-Temperature PEM Fuel Cell Stack Operated with Polybenzimidazole Based Membranes. International Journal of Hydrogen Energy, 45, 35198-35207. https://doi.org/10.1016/j.ijhydene.2019.11.173
Ryu, S.K., Vinothkannan, M., Kim, A.R. and Yoo, D.J. (2022) Effect of Type and Stoichiometry of Fuels on Performance of Polybenzimidazole-Based Proton Exchange Membrane Fuel Cells Operating at the Temperature Range of 120 - 160 °C. Energy, 238, Article ID: 121791. https://doi.org/10.1016/j.energy.2021.121791
Kim, D.H., Min, C.M., Lee, E., Lee, J.S. and Pak, C. (2020) Effect of Vinylphosphonic Acid and Polymer Binders with Phosphate Groups on Performance of High-Temperature Polymer Electrolyte Membrane Fuel Cell. Catalysis Today, 358, 333-337. https://doi.org/10.1016/j.cattod.2019.07.046
Jia, T., Shen, S., Zhao, J., Jin, J., Pan, B., Duan, X., Meng, C. and Che, Q. (2020) Ultrathin Membranes Formation via the Layer by Layer Self-Assembly of Carbon Nanotubes-Based Inorganics as High Temperature Proton Exchange Membranes. International Journal of Hydrogen Energy, 45, 14517-14527. https://doi.org/10.1016/j.ijhydene.2020.03.175
Wang, D., Wang, S., Tain, X., Li, J., Liu, F., Wang, X., Chen, H., Mao, T. and Liu, G. (2020) Ethyl Phosophoric Acid Grafted Amino-Modified Polybenzimidazole with Improved Long-Term Stability for High-Temperature Proton Exchange Membrane Proton Exchange Membrane Applications. International Journal of Hydrogen Energy, 45, 3176-3185. https://doi.org/10.1016/j.ijhydene.2019.11.219
Zhang, J., Wang, H., Li, W., Zhang, J., Lu, D., Yan, W., Xiang, Y. and Lu, S. (2021) Effect of Catalyst Layer Microstructures on Performance and Stability for High Temperature Polymer Electrolyte Membrane Fuel Cells. Journal of Power Sources, 505, Article ID: 230059. https://doi.org/10.1016/j.jpowsour.2021.230059
Lee, W.J., Lee, J.S., Park, H.Y., Park, H.S., Lee, S.Y., Song, K.H. and Kim, H. (2020) Improvement of Fuel Cell Performances through the Enhanced Dispersion of the PEFC Binder in Electrodes for Use in High Temperature Polymer Electrolyte Membrane Fuel Cells. International Journal of Hydrogen Energy, 45, 32825-32833. https://doi.org/10.1016/j.ijhydene.2020.03.095
Xu, Y., Fan, R., Chang, G., Xu, S. and Cai, T. (2021) Investigating Temperature-Driven Water Transport in Cathode Gas Diffusion Media of PEMFC with a Non-Isothermal, Two-Phase Model. Energy Conversion and Management, 248, Article ID: 114791. https://doi.org/10.1016/j.enconman.2021.114791
Xia, L., Ni, M., Xu, Q., Xu, H. and Zheng, K. (2021) Optimization of Catalyst Layer Thickness for Achieving High Performance and Low Cost of High Temperature Proton Exchange Membrane Fuel Cell. Applied Energy, 294, Article ID: 117012. https://doi.org/10.1016/j.apenergy.2021.117012
Das, S.K. and Gibson, H.A. (2021) Three Dimensional Multi-Physics Modeling and Simulation for Assessment of Mass Transport Impact on the Performance of a High Temperature Polymer Electrolyte Fuel Cell. Journal of Power Sources, 499, Article ID: 229844. https://doi.org/10.1016/j.jpowsour.2021.229844
Xia, L., Ni, M., He, Q., Xu, Q. and Cheng, C. (2021) Optimization of Gas Diffusion Layer in High Temperature PEMFC with the Focuses on Thickness and Porosity. Applied Energy, 300, Article ID: 117357. https://doi.org/10.1016/j.apenergy.2021.117357
Huang, T., Wang, W., Yuan, Y., Huang, J., Chen, W., Zhang, J., Kong, X., Zhang, Y. and Wan, Z. (2021) Optimization of High-Temperature Proton Exchange Membrane Fuel Cell Flow Channel Based on Genetic Algorithm. Energy Reports, 7, 1374-1384. https://doi.org/10.1016/j.egyr.2021.02.062
Chen, H., Guo, H., Ye, F. and Ma, C.F.A. (2021) Numerical Study of Oriented-Type Flow Channels with Porous-Blocked Baffles of Proton Exchange Membrane Fuel Cells. International Journal of Hydrogen Energy, 46, 29443-29458. https://doi.org/10.1016/j.ijhydene.2020.12.178
Zhang, T., Li, J., Li, Q., Yu, M. and Sun, H. (2021) Combination Effects of Flow Field Structure and Assembly Force on Performance of High Temperature Proton Exchange Membrane Fuel Cells. International Journal of Energy Research, 45, 7903-7917. https://doi.org/10.1002/er.6374
Xia, L., Xu, Q., He, Q., Ni, M. and Seng, M. (2021) Numerical Study of High Temperature Proton Exchange Membrane Fuel Cell (HT-PEMFC) with a Focus on Rib Design. International Journal of Hydrogen Energy, 46, 21098-21111. https://doi.org/10.1016/j.ijhydene.2021.03.192
Nanadegani, F.S., Lay, E.N. and Sunden, B. (2020) Computational Analysis of the Impact of a Micro Porous Layer (MPL) on the Characteristics of a High Temperature PEMFC. Electrochimica Acta, 333, Article ID: 135552. https://doi.org/10.1016/j.electacta.2019.135552
Nishimura, A., Kono, N., Toyoda, K., Kojima, M. and Kolhe, M.L. (2021) Impact Analysis of MPL on a PEFC Cell’s Temperature Distribution with Thin PEM and GDL for Operating at Higher Temperature than Usual. Journal of Energy and Power Engineering, 15, 39-51. https://doi.org/10.17265/1934-8975/2021.02.001
Nishimura, A., Yamamoto, K., Okado, T., Kojima, Y., Hirota, M. and Kolhe, M. (2020) Impact of Analysis of MPL and PEM Thickness on Temperature Distribution within PEFC Operating at Relatively Higher Temperature. Energy, 205, Article ID: 117875. https://doi.org/10.1016/j.energy.2020.117875
Nishimura, A., Sato, Y., Kamiya, S., Okado, T., Yamamoto, K., Hirota, M. and Hu, E. (2019) Impact of Thickness of Polymer Electrolyte Membrane and Gas Diffusion Layer on Temperature Distribution in Polymer Electrolyte Fuel Cell Operated at Temperature around 90 °C. Journal of Energy and Power Engineering, 13, 97-115. https://doi.org/10.17265/1934-8975/2019.03.002
Nishimura, A., Sato, Y., Yoshimura, M., Kamiya, S. and Hirota, M. (2018) Impact of Thickness of Polymer Electrolyte Membrane on Temperature Distribution in Single Cell of Polymer Electrolyte Fuel Cell Operated at High Temperature. Journal of Energy and Power Engineering, 12, 80-92. https://doi.org/10.17265/1934-8975/2018.02.004
Nishimura, A., Shibuya, K., Morimoto, A., Tanaka, S., Hirota, M., Nakamura, Y., Kojima, M., Narita, M. and Hu, E. (2012) Dominant Factor and Mechanism of Coupling Phenomena in Single Cell of Polymer Electrolyte Fuel Cell. Applied Energy, 90, 73-79. https://doi.org/10.1016/j.apenergy.2011.01.003
Nishimura, A., Okado, T., Kojima, Y. and Hu, E. (2021) Impact of Microporous Layer on Heat and Mass Transfer in a Single Cell of Polymer Electrolyte Fuel Cell Using a Thin Polymer Electrolyte Membrane and a Thin Gas Diffusion Layer Operated at a High-Temperature Range. ACS Omega, 6, 14575-14584. https://doi.org/10.1021/acsomega.1c01693
Zamel, N., Becker, J. and Wiegmann, A. (2012) Estimating the Thermal Conductivity and Diffusion Coefficient of the Microporous Layer of Polymer Electrolyte Membrane Fuel Cells. Journal of Power Sources, 207, 70-80. https://doi.org/10.1016/j.jpowsour.2012.02.003
Chen, G., Zhang, G., Guo, L. and Liu, H. (2016) Systematic Study on the Functions and Mechanisms of Micro Porous Layer on Water Transport in Proton Exchange Membrane Fuel Cells. International Journal of Hydrogen Energy, 41, 2334-2441. https://doi.org/10.1016/j.ijhydene.2016.01.074
Nishimura, A., Fukuoka, T., baba, M., Hirota, M. and Hu, E. (2015) Clarification of Temperature Distribution in Single Cell of Polymer Electrolyte Fuel Cell under Different Operation Conditions by Means of 1D Multi-Plate Heat-Transfer Model. Journal of Chemical Engineering of Japan, 48, 862-871. https://doi.org/10.1252/jcej.14we200
Alizadeh, E., Rahmi-Ebso, M., Rahgoshay, S.M. and Saadat, S.H.M. (2017) Numerical and Experimental Investigation of Cascade Type Serpentine Flow Filed of Reactant Gases for Improving Performance of PEM Fuel Cell. International Journal of Hydrogen Energy, 42, 14708-14724. https://doi.org/10.1016/j.ijhydene.2017.04.212
Copper, N.J., Santamaria, A.D., Becton, M.K. and Park, J.W. (2017) Neutron Radiography Measurements of In-Situ PEMFC Liquid Water Saturation in 2D & 3D Morphology Gas Diffusion Layers. International Journal of Hydrogen Energy, 42, 14708-14724. https://doi.org/10.1016/j.ijhydene.2017.05.105
Khandewal, M. and Mench, M.M. (2006) Direct Measurement of Though-Plane Thermal Conductivity and Contract Resistance in Fuel Cell Materials. Journal of Power Sources, 161, 1106-1115. https://doi.org/10.1016/j.jpowsour.2006.06.092
The Japan Society of Mechanical Engineers (1993) JSME Heat Transfer Handbook. Maruzen, Tokyo, 367-369.
Nishimura, A., Toyoda, K., Kojima, Y., Ito, S. and Hu, E. (2021) Numerical Simulation on Impacts of Thickness of Nafion Series Membranes and Relative Humidity on PEMFC Operated at 363 K and 373 K. Energies, 14, Article 8256. https://doi.org/10.3390/en14248256
Sunakawa, D., Oyama, S., Araki, T. and Onda, K. (2006) Measurement of Diffusion Coefficient and Electro-Osmotic Coefficient of Water at PEFC. Electrochemistry, 74, 732-736. https://doi.org/10.5796/electrochemistry.74.732
Reid, R.C., Prausnitz, J.M. and Poling, B.E. (1987) The Properties of Gases and Liquids. McGraw-Hill Book Company, New York, 589-591.
Kawase, M., Inagaki, T., Kawashimra, S. and Miura, K. (2009) Effective Thermal Conductivity of Gas Diffusion Layer in Through-Plane Direction. ECS Transactions, 25, 1529-1537. https://doi.org/10.1149/1.3210709
Jung, C.Y., Shim, H.S., Koo, S.M., Lee, S.H. and Yi, S.C. (2012) Investigation of the Temperature Distribution in Proton Exchange Membrane Fuel Cell. Applied Energy, 93, 733-741. https://doi.org/10.1016/j.apenergy.2011.08.035
Nishimura, A., Iio, K., Baba, M., Yamauchi, T., Hirota, M. and Hu, E. (2014) Modeling of Heat Transfer in Single Cell of Polymer Electrolyte Fuel Cell by Means of Temperature Data Measured by Thermograph. Journal of Chemical Engineering of Japan, 47, 521-529. https://doi.org/10.1252/jcej.13we275
Nishimura, A., Zamami, K. P., Yoshimura, M., Hirota, M. and Kolhe, M.L. (2017) Numerical Analysis of Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell When Operated in Elevated Temperature Range. Journal of Energy and Power Engineering, 11, 393-408. https://doi.org/10.17265/1934-8975/2017.06.005
Japan Meteorological Agency (2022) Weather Forecast.
Nishimura, A., Kojima, Y., Ito, S. and Hu, E. (2022) Impacts of Separator Thickness on Temperature Distribution and Power Generation Characteristics of a Single PEMFC Operated at Higher Temperature of 363 and 373 K. Energies, 15, Article 1558. https://doi.org/10.3390/en15041558
Nishimura, A., Osada, K., Tsunoda, T., Yoshimura, M., Hirota, M. and Hu, E. (2016) Analysis on Temperature Distribution in Single Cell of Polymer Electrolyte Fuel Cell When Operated in High Temperature Range. Journal of Energy and Power Engineering, 10, 453-464. https://doi.org/10.17265/1934-8975/2016.08.001
Xu, Z., Qiu, D., Yi, P., Peng, L. and Lai, X. (2020) Towards Mass Applications: A Review on the Challenges and Developments in Metallic Bipolar Plates for PEMFC. Progress in Natural Science: Materials International, 46, 8672-8701.
Wu, S., Yang, W., Yan, H., Zuo, X., Cao, Z., Li, H., Shi, M. and Chen, H. (2021) A Review of Modified Metal Bipolar Plates for Proton Exchange Membrane Fuel Cells. International Journal of Hydrogen Energy, 46, 8672-8701. https://doi.org/10.1016/j.ijhydene.2020.12.074
Saadat, N., Dhakal, H.N., Tjong, J., Jaffer, S., Yang, W. and Sain, M. (2021) Recent Advances and Future Perspectives of Carbon Materials for Fuel Cell. Renew and Sust. Energy Reviews, 138, Article ID: 110535. https://doi.org/10.1016/j.rser.2020.110535