Experimental Study on the Cyclic Ampacity and Its Factor of 10 kV XLPE Cable
- 1 School of Electric Power, South China University of Technology, Guangzhou, China Foshan Power Bureau of Guangdong Power Grid Company, Foshan, China
- 2 School of Electric Power, South China University of Technology, Guangzhou, China Foshan Power Bureau of Guangdong Power Grid Company, Foshan, China
- 3 School of Electric Power, South China University of Technology, Guangzhou, China Foshan Power Bureau of Guangdong Power Grid Company, Foshan, China
- 4 School of Electric Power, South China University of Technology, Guangzhou, China Foshan Power Bureau of Guangdong Power Grid Company, Foshan, China
- 5 School of Electric Power, South China University of Technology, Guangzhou, China Foshan Power Bureau of Guangdong Power Grid Company, Foshan, China
Abstract
The load varies periodically, but the peak current of power cable is controlled by its continuous ampacity in China, resulting in the highest conductor temperature is much lower than90 ℃ , the permitted long-term working temperature of XLPE. If the cable load is controlled by its cyclic ampacity, the cable transmission capacity could be used sufficiently. To study the 10 kV XLPE cable cyclic ampacity and its factor, a three-core cable cyclic ampacity calculation software is developed and the cyclic ampacity experiments of direct buried cable are undertaken in this paper. Experiments and research shows that the software calculation is correct and the circuit numbers and daily load factor have an important impact on the cyclic ampacity factor. The cyclic ampacity factor of 0.7 daily load factor is 1.20, which means the peak current is the 1.2 times of continuous ampacity. If the continuous ampacity is instead by the cyclic ampacity to control the cable load, the transmission capacity of the cable can be improved greatly without additional investment.
- W. Y. Yang, “Studying on the On-line Temperature Monitoring System for Power Cable,” Master Thesis, Northeast Dianli University, Jilin, 2008.
- X. B. Yin, “The Study of Calculation of the Cyclic Current Rating for 110 kV or above High Voltage Cables,” Master Thesis, Shanghai Jiao Tong University, Shanghai, 2009.
- IEC Standard 60853, “Calculation of the Cyclic and Emergency Current Rating of Cables,” 1st Edition 1989, 2nd Edition 1994.
- G. D. Ma, “Electric Wire and Cable Capacity,” China Water Power Press, Beijing, China, 2003.
- G. Anders, “Rating of Electric Power Cables in Unfavorable Thermal Environment,” 1st Edition, Wiley-IEEE Press, 2005.
- J. K. Zhao, Y. Jiang, L. M. Yang and L. H. Xu, “Experimental Research for the Current Rating of Medium and Low Voltage XLPE Cables in Cluster Laying,” High Voltage Engineering, Vol. 31, No. 10, 2005, pp. 55-58. doi:10.3969/j.issn.1003-6520.2005.10.020
- H. Q. Niu and X. Zhou, “Calculation and Experiment of Transient Temperatures of Single-core Cables on Jacket Temperature Monitoring,” High Voltage Engineering, Vol. 35, No. 9, 2009, pp. 2138-2143.
- Y. Zhang, X. Zhou, H. Q. Niu, X. B. Wang, Y. Tang, J. K. Zhao., et al., “Theoretical Calculation and Experimental Research on Thermal Time Constant of Single-core Cables,” High Voltage Engineering, Vol. 35, No. 11, 2009, pp. 2801-2806.
- Y. L. Zheng, “The Calculation of the Steady-state Temperature Field and Rated Ampacity of 10 kV XLPE Power Cables,” Journal of Baoji University of Arts and Sciences (Natural Science Edition), Vol. 29, No. 2, 2009, pp. 59-62. doi:10.3969/j.issn.1007-1261.2009.02.018
- Y. Tang, X. B. Wang, Y. P. Chen, H. Q. Niu, Y. Zhang, Y. B. Fan, et al., “Experimental Research on the Current Rating of 10 kV Three-core XLPE Cables,” High Voltage Engineering, Vol. 35, No. 11, 2009, pp. 2807-2811.