A Cell Model to Describe and Optimize Heat and Mass Transfer in Contact Heat Exchangers
- 1
- 2
- 3
Abstract
A cell model to describe and optimize heat and mass transfer in contact heat exchangers for utilization of exhaust gases heat is proposed. The model is based on the theory of Markov chains and allows calculating heat and mass transfer at local moving force of the processes in each cell. The total process is presented as two parallel chains of cells (one for water flow and one for gas flow). The corresponding cells of the chains can exchange heat and mass, and water and gas can travel along their chains according to their transition ma-trices. The results of numerical experiments showed that the most part of heat transfer occurs due to moisture condensation from gas and the most intense heat transfer goes near the inlet of gas. Experimental validation of the model showed a good correlation between calculated and experimental data for an industrial contact heat exchanger if appropriate empirical equations were used to calculate heat and mass transfer coefficient. It was also shown that there exists the optimum height of heat exchanger that gave the maximum gain in heat energy utilization.
- K. Nagano, S. Takeda, T. Mochida and K. Shimakura, “Thermal Characteristics of a Direct Heat Exchange System between Granules with Phase Change Material and Air,” Applied Thermal Engineering, Vol. 24, No. 14-15, 2004, pp. 2131-2144. doi:10.1016/j.applthermaleng.2004.02.004
- S. S. Gulawani, S. K. Dahikar, C. S. Mathpati, J. B. Joshi, M. S. Shah, C. S. RamaPrasad and D. S. Shukla, “Analysis of Flow Pattern and Heat Transfer in Direct Contact Condensation,” Chemical Engineering Science, Vol. 64, No. 8, 2009, pp. 1719-1738. doi:10.1016/j.ces.2008.12.020
- S. B. Geni?, “Direct-Contact Condensation Heat Transfer on Downcommerless Trays for Steam-Water System,” International Journal of Heat and Mass Transfer, Vol. 49, No. 7-8, 2006, pp. 1225-1230. doi:10.1016/j.ijheatmasstransfer.2005.10.003
- B. M. Smolsky and G. T. Sergeyev, “Heat and Mass Transfer with Liquid Evaporation,” International Journal of Heat and Mass Transfer, Vol. 5, No. 10, 1962, pp. 1011-1021. doi:10.1016/0017-9310(62)90081-9
- M. Farid and K. Yacoub, “Performance of Direct Contact Latent Heat Storage Unit,” Solar Energy, Vol. 43, No. 4, 1989, pp. 237-251. doi:10.1016/0038-092X(89)90023-6
- J. Siqueiros and O. Bonilla, “An Experimental Study of a Three-Phase, Direct-Contact Heat Exchanger,” Applied Thermal Engineering, Vol. 19, No. 5, 1999, pp. 477-493. doi:10.1016/S1359-4311(98)00068-4
- M. C. De Andrés, E. Hoo, and F. Zangrando, “Performance of Direct-Contact Heat and Mass Exchangers with Steam-Gas Mixtures at Subatmospheric Pressures,” International Journal of Heat and Mass Transfer, Vol. 39, No. 5, 1996, pp. 965-973. doi:10.1016/0017-9310(95)00173-5
- I. Z. Aronov, “Contact Heating Water by Combustion Products of Natural Gas,” Nauka Publishers, Moscow, 1990.
- J. Mitrovic and K. Stephan, “Mean Fluid Temperatures in Direct Contact Heat Exchangers without Phase Change,” International Journal of Heat and Mass Transfer, Vol. 39, No. 13, 1996, pp. 2745-2750. doi:10.1016/0017-9310(95)00357-6
- L. Tadrist, P. Seguin, R. Santini, J. Pantaloni and A. Bricard, “Experimental and Numerical Study of Direct Contact Heat Exchangers,” International Journal of Heat and Mass Transfer, Vol. 28, No. 6, 1985, pp. 1215-1227. doi:10.1016/0017-9310(85)90129-2
- H. Belghazi, M. El Ganaoui and J.C. Labbe, “Analytical Solution of Unsteady Heat Conduction in a Two-Layered Material in Imperfect Heat Subjected to a Moving Heat Source,” International Journal of Thermal Sciences, Vol. 49, No. 2, 2010, pp. 311-318. doi:10.1016/j.ijthermalsci.2009.06.006