The development of power conversion systems based on fuel cells has been demanding reliability studies since the requirements associated with cost and durability of these technological products have become fundamental to their acceptance by the energy market. The experimental part of the reliability study presented in this work consisted of performing life tests with single proton exchange membrane fuel cells (PEMFCs). The proposed reliability analysis methodology covered the application of qualitative and quantitative techniques. In the qualitative approach, a Failure Mode and Effect Analysis was developed in order to identify and evaluate all potential failures associated with the operation of fuel cells. In the quantitative approach, a statistical analysis was applied to the sample data generated in long-term steady-state tests of these devices. A two-parameter exponential distribution was fitted to data and the maximum likelihood estimate for the mean time to failure (MTTF) of the fuel cells was calculated. It is important to point out that the tests performed under the scope of this study were the first long-term experiments performed with the fuel cells produced in the laboratories of IPEN-CNEN/SP, Brazil. Although the results indicated that fuel cell performance and durability were still at a level below the targets normally established for similar commercial devices, the improvement of the main components of PEMFCs has been the objective of several projects developed at the institute. Thus, the main benefit brought by this study is the proposed methodology, which can be implemented as part of a reliability growth analysis of the fuel cells and can be integrated into the design process of these devices.
Linardi, M. (2010) Introducao à Ciência e Tecnologia de Células a Combustível. Artliber, Sao Paulo.
Wendt, H., Linardi, M. and Aricó, E.M. (2002) Células a Combustível de Baixa Potência para Aplicacoes Estacionárias, Química Nova, 25, 470-476. https://doi.org/10.1590/S0100-40422002000300021
Nonobe, Y. (2017) Development of the Fuel Cell Vehicle Mirai. IEEJ Transactions on Electrical and Electronic Engineering, 12, 5-9. https://doi.org/10.1002/tee.22328
Lipman, T.E. (2017) Emerging Technologies for Higher Fuel Economy Automobile Standards. Annual Review of Environment and Resources, 42, 267-288. https://doi.org/10.1146/annurev-environ-110615-085844
Serov, A. and Kwak, C. (2009) Progress in Development of Direct Dimethyl Ether Fuel Cells. Applied Catalysis B: Environmental, 91, 1-10. https://doi.org/10.1016/j.apcatb.2009.06.018
Li, D., Lv, H., Kang, Y., Markovic, N.M. and Stamenkovic, V.R. (2016) Progress in the Development of Oxygen Reduction Reaction Catalysts for Low-Temperature Fuel Cells. Annual Review of Chemical and Biomolecular Engineering, 7, 509-532. https://doi.org/10.1146/annurev-chembioeng-080615-034526
US Department of Energy: Fuel Cells Technologies Office Multi-Year Research, Development, and Demonstration Plan. https://www.energy.gov/eere/fuelcells/downloads/fuel-cell-technologies-office-multi-year-research-development-and-22
Whiteley, M., Fly, A., Leigh, J., Dunnett, S. and Jackson, L. (2015) Advanced Reliability Analysis of Polymer Electrolyte Membrane Fuel Cells Using Petri-Net Analysis and Fuel Cell Modelling Techniques. International Journal of Hydrogen Energy, 40, 11550-11558. https://doi.org/10.1016/j.ijhydene.2015.01.154
Whiteley, M., Dunnett, S. and Jackson, L. (2016) Failure Mode and Effect Analysis, and Fault Tree Analysis of Polymer Electrolyte Membrane Fuel Cells. International Journal of Hydrogen Energy, 41, 1187-1202. https://doi.org/10.1016/j.ijhydene.2015.11.007
Placca, L. and Kouta, R. (2011) Fault Tree Analysis for PEM Fuel Cell Degradation Process Modelling. International Journal of Hydrogen Energy, 36, 12393-12405. https://doi.org/10.1016/j.ijhydene.2011.06.093
Ireson, W.G., Coombs, C.F. and Moss, R.Y. (1996) Handbook of Reliability Engineering and Management. 2nd Edition, McGraw Hill, New York.
McDermott, R.E., Mikulak, R.J. and Beauregard, M.R. (1996) The Basics of FMEA. Quality Resources, New York.
Freitas, M.A. and Colosimo, E.A. (1997) Confiabilidade: Análise de Tempo de Falhas e Testes de Vida Acelerados. Fundacao Christiano Ottoni, Belo Horizonte.
Fowler, M.W., Mann, R.F., Amphlett, J.C., Peppley, B.A. and Roberge, P.R. (2002) Incorporation of Voltage Degradation into a Generalised Steady State Electrochemical Model for a PEM Fuel Cell. Journal of Power Sources, 106, 274-283. https://doi.org/10.1016/S0378-7753(01)01029-1
Kundu, S., Fowler, M.W., Simon, L.C. and Grot, S. (2006) Morphological Features (Defects) in Fuel Cell Membrane Electrode Assemblies. Journal of Power Sources, 157, 650-656. https://doi.org/10.1016/j.jpowsour.2005.12.027
De Bruijn, F.A., Dam, V.A.T. and Janssen, G.J.M. (2007) Review: Durability and Degradation Issues of PEM Fuel Cell Components. Fuel Cells, 8, 3-22. https://doi.org/10.1002/fuce.200700053
Cleghorn, S.J.C., Mayfield, D.K., Moore, D.A., Moore, J.C., Rusch, G., Sherman, T.W., Sisofo, N.T. and Beuscher, U. (2006) A Polymer Electrolyte Fuel Cell Life Test: 3 Years of Continuous Operation. Journal of Power Sources, 158, 446-454. https://doi.org/10.1016/j.jpowsour.2005.09.062
Liu, D. and Case, S. (2006) Durability Study of Proton Exchange Membrane Fuel Cells Under Dynamic Testing Conditions with Cyclic Current Profile. Journal of Power Sources, 162, 521-531. https://doi.org/10.1016/j.jpowsour.2006.07.007
Schmittinger, W. and Vahidi, A. (2008) A Review of the Main Parameters Influencing Long-Term Performance and Durability of PEM Fuel Cells. Journal of Power Sources, 180, 1-14. https://doi.org/10.1016/j.jpowsour.2008.01.070
Wu, J., Yuan, X.Z., Martin, J.J., Wang, H., Zhang, J., Shen, J., Wu, S. and Merida, W. (2008) A Review of PEM Fuel Cell Durability: Degradation Mechanisms and Mitigation Strategies. Journal of Power Sources, 184, 104-119. https://doi.org/10.1016/j.jpowsour.2008.06.006
Marrony, M., Barrera, R., Quenet, S., Ginocchio, S., Montelatici, L. and Aslanides, A. (2008) Durability Study and Lifetime Prediction of Baseline Proton Exchange Membrane Fuel Cell Under Severe Operating Conditions. Journal of Power Sources, 182, 469-475. https://doi.org/10.1016/j.jpowsour.2008.02.096
Borup, R., Meyers, J., Pivovar, B., Kim, Y.S., Mukundan, R., Garland, N., Myers, D., Wilson, M., Garzon, F., Wood, D., Zelenay, P., More, K., Stroh, K., Zawodzinski, T., Boncella, J., McGrath, J.E., Inaba, M., Miyatake, K., Hori, M., Ota, K., Ogumi, Z., Miyata, S., Nishikata, A., Siroma, Z., Uchimoto, Y., Yasuda, K., Kimijima, K.I. and Iwashita, N. (2007) Scientific Aspects of Polymer Electrolyte Fuel Cell Durability and Degradation. Chemical Reviews, 107, 3904-3951. https://pubs.acs.org/doi/abs/10.1021/cr050182l https://doi.org/10.1021/cr050182l
Meeker, W.Q. and Scobar, L.A. (1998) Statistical Methods for Reliability Data. John Wiley & Sons, New York.
Nelson, W.B. (1998) Applied Life Data Analysis. John Wiley & Sons, New York.
Lawless, J.F. (2003) Statistical Models and Methods for Lifetime Data. 2nd Edition, John Wiley & Sons, New York. https://doi.org/10.1002/9781118033005
European Commission (2010) Testing the Voltage and Power as Function of Current Density: Polarisation Curve for a SOFC Single Cell. JRC Scientific and Technical Reports.
European Commission (2010) Testing the Voltage and Power as Function of Current Density Following an On/Off Profile versus Time: Accelerated Ageing On/Off Cycling Test for a PEFC Single Cell. JRC Scientific and Technical Reports.
European Commission (2010) Testing the Voltage and Power as Function of Current Density: Long Term Durability Steady Test for a Single PEFC. JRC Scientific and Technical Reports.
Malkow, T., De Marco, G., Pilenga, A., Honselaar, M., Tsotridis, G., Escribano, S., Antoni, L., Rei?ner, R., Thalau, O., Sitters, E. and Heinz, G. (2010) Testing the Humidification Sensitivity of a Single PEFC-Characterisation of the Performances of a PEFC Operating with Fuel and Oxidant at Various Relative Humidity. JRC Scientific and Technical Reports.
Andrade, A.B., Bejarano, M.L.M., Cunha, E.F., Robalinho, E. and Linardi, M. (2009) Fabrication of High Precision PEMFC Membrane Electrode Assemblies by Sieve Printing Method. Journal of Fuel Cell Science and Technology, 6, Article ID: 021305.
ReliaSoft Corporation, Weibull++ Version 6, Tucson-AZ, 1992-2000.