Ball Milling and Annealing of Co-50 at% W Powders
- 1 Department of Engineering Metallurgy, University of Johannesburg, Johannesburg, South Africa
- 2 Transnet Rail Engineering, Pretoria, South Africa
- 3 DST/CSIR Nanotechnology Innovation Centre, National Centre of Nano-Structured Materials, Council for Scientific and Industrial Research, Pretoria, South Africa
Abstract
Broadening and height reduction of X-ray diffraction peaks were observed after cold-pressing of unmilled Co-W pow der mixture. It seems the effect of cold pressing has slightly reduced the lattice parameter of W from 3.165 to 3.143 ? . Consequent annealing of unmilled compacts yielded metastable phases. Upon 10 and 20 h ball milling of Co-W powder, no alloying was obtained. Although milling did not yield significant crystal changes in W and Co ground state struc tures, its effect is evident during subsequent annealing. An eta phase is obtained for the first time from unmilled-an nealed Co-W powder mixture in the absence of interstitial elements like carbon, while the milled counterpart yielded the rhombohedral Co 7 W 6 -type phase with composition deviated from stoichiometric value.
- M. Donten and Z. Stojek, “Pulse Electroplating of Rich in-Tungsten Thin Layers of Amorphous Co-W Alloys,” Journal of Applied Electrochemistry, Vol. 26, No. 6, 1996, pp. 665-672. doi:10.1007/BF00253466
- D. Z. Grabco, I. A. Dikusar, V. I. Petrenko, E. E. Harea and O. A. Shikimaka, “Micromechanical Properties of Co-W Alloys Electrodeposited under Pulse Conditions,” Surface Engineering of Applied Electrochemistry, Vol. 43, No. 1, 2007, pp. 11-17. doi:10.3103/S1068375507010024
- S. S. Grabchikov and A. M. Yaskovich, “Effect of the Structure of Amorphous Electrodeposited Ni-W and Ni Co-W Alloys on Their Crystallization,” Russian Metal lurgy, Vol. 2006, No. 1, 2006, pp. 56-60. doi:10.1134/S0036029506010101
- Z. Guo, X. Zhu, D. Zhai and X. Yang, “Electrodeposition of Ni-W Amorphous Alloy and Ni-W-SiC Composite Deposits,” Journal of Materials Science and Technology, Vol. 16, No. 2, 2000, pp. 323-326.
- C. Borgia, T. Scharowsky, A. Furrer, C. Solenthaler and R. Spolenak, “A Combinational Study on the Influence of Elemental Composition and Heat Treatment on the Phase Composition, Microstructure and Mechanical Properties of Ni-W Alloy Thin Films,” Acta Materialia, Vol. 59, No. 1, 2011, pp. 386-399. doi:10.1016/j.actamat.2010.09.045
- B. Yang, G. Qin, W. Pei, Y. Ren, N. Xiao and X. Zhao, “Abnormal Saturation Magnetization Dependency on W Content for Co-W Thin Films,” Acta Metalligica Sinica, Vol. 23, No. 1, 2010, pp. 8-12.
- M. Mulukutla, V. K. Kommineni and S. P. Harimkar, “Pulsed Electrodeposition of Co-W Amorphous and Crystalline Coatings,” Applied Surface Science, Vol. 258, No. 7, 2012, pp. 2886-2893. doi:10.1016/j.apsusc.2011.11.002
- K. Wikiel and J. Osteryoung, “Voltammetric Study of Plating Baths for Electrodeposition of Co-W Amorphous Alloys,” Journal of Applied Electrochemistry, Vol. 22, No. 6, 1992, pp. 506-511. doi:10.1007/BF01024089
- S. Bolokang, C. Bangayayi and M. Phasha, “Effect of C and Milling Parameters on the Synthesis of WC Powders by Mechanical Alloying,” International Journal of Refractory Metals and Hard Materials, Vol. 28, No. 2, 2010, pp. 211-216. doi:10.1016/j.ijrmhm.2009.09.006
- K. F. Kobayashi and H. Kawaguchi, “Amorphization of Al-Cr Atomized Powder by Mechanical Alloying,” Materials Science and Engineering A, Vol. 181-182, 1994, pp. 1253-1257. doi:10.1016/0921-5093(94)90841-9
- A. Karin, A. Bonefacic and D. Duzevic, “Phase Trans formation in Pressed Cobalt Powder,” Journal of Physics F: Metal Physics, Vol. 14, No. 11, 1984, pp. 2781-2786. doi:10.1088/0305-4608/14/11/030