Numerical Study on Heat Transfer Characteristics of Heated/Cooled Rods Having a Composite Board in between: Effect of Thermal Vias
- 1 Division of Energy Science, Faculty of Advanced Science and Technology, Kumamoto University, Kumamoto, Japan
- 2 Division of Energy Science, Faculty of Advanced Science and Technology, Kumamoto University, Kumamoto, Japan
Abstract
By placing a sample between a heated and a cooled rod, a thermal conductivity of the sample can be evaluated easily with the assumption of a one-dimensional heat flow. However, a three-dimensional constriction/spreading heat flow may occur inside the rods when the sample is a composite having different thermal conductivities. In order to investigate the thermal resistance due to the constriction/spreading heat flow, the three-dimensional numerical analyses were conducted on the heat transfer characteristics of the rods. In the present analyses, a polymer-based composite board having thermal vias was sandwiched between the rods. From the numerical results, it was confirmed that the constriction/spreading resistance of the rods was strongly affected by the thermal conductivity of the rods as well as the number and size of the thermal vias. A simple equation was also proposed to evaluate the constriction/spreading resistance of the rods. Fairly good agreements were obtained between the numerical results and the calculated ones by the simple equation. Moreover, the discussion was also made on an effective thermal conductivity of the composite board evaluated with the heated and the cooled rod.
- ASTM E1225-04 (2004) Standard Test Method for Thermal Conductivity of Solids by Means of the Guarded-Comparative-Longitudinal Heat Flow Technique. ASTM International, West Conshohocken.
- Tomimura, T., Shiotsu, Y., Koito, Y., Ishizuka, M. and Hatakeyama, T. (2011) Evaluation of Effective Thermal Conductivity of Multilayer Printed Circuit Board. Proceedings of 8th ASME/JSME Thermal Engineering Joint Conference, Honolulu, 13-17 March 2011, AJTEC2011-44232.
- Sadeghi, E., Hsieh, S. and Bahrami, M. (2011) Thermal Conductivity and Contact Resistance of Metal Foams. Journal of Physics D: Applied Physics, 44, Article ID: 125406. https://doi.org/10.1088/0022-3727/44/12/125406
- Yovanovich, M.M. and Marotta, E.E. (2003) Thermal Spreading and Contact Resistances. In: Bejan, A. and Kraus, A.D., Eds., Heat Transfer Handbook, John Wiley & Sons, Inc., Hoboken, 261-393.
- Rahmani, Y., Ganji, D.D. and Bandpy, M.G. (2016) Analytical Study of Thermal Spreading Resistance in Curved-Edge Heat Spreader. Applied Thermal Engineering, 104, 527-533. https://doi.org/10.1016/j.applthermaleng.2016.05.107
- Kumar, S. and Tariq, A. (2017) Steady State Experimental Investigation of Thermal Contact Conductance between Curvilinear Contacts Using Liquid Crystal Thermography. International Journal of Thermal Sciences, 118, 53-68. https://doi.org/10.1016/j.ijthermalsci.2017.04.014
- Koito, Y., Kubo, Y. and Tomimura, T. (2013) Numerical Analysis of Printed Circuit Board with Thermal Vias: Heat Transfer Characteristics under Nonisothermal Boundary Conditions. Journal of Electronics Cooling and Thermal Control, 3, 136-143. https://doi.org/10.4236/jectc.2013.34015
- Wits, W.W. and Kok, J.B.W. (2011) Modeling and Validating the Transient Behavior of Flat Miniature Heat Pipes Manufactured in Multilayer Printed Circuit Board Technology. ASME Journal of Heat Transfer, 133, Article ID: 081401.
- Oshman, C., Shi, B., Li, C., Yang, R., Lee, Y.C., Peterson, G.P. and Bright, V.M. (2011) The Development of Polymer-Based Flat Heat Pipes. Journal of Microelectromechanical Systems, 20, 410-417. https://doi.org/10.1109/JMEMS.2011.2107885
- Yang, K.S., Yang, T.Y., Tu, C.W., Yeh, C.T. and Lee, M.T. (2015) A Novel Flat Polymer Heat Pipe with Thermal Via for Cooling Electronic Devices. Energy Conversion and Management, 100, 37-44. https://doi.org/10.1016/j.enconman.2015.04.063