Fabrication and Investigation of Damping Properties of Nano Particulate Composites
- 1 Department of Mechanical Engineering, National Institute of Technology Karnataka, Surathkal,India-575025.
- 2 Department of Mechanical Engineering, National Institute of Technology Karnataka, Surathkal,India-575025.
- 3 Department of Mechanical Engineering, National Institute of Technology Karnataka, Surathkal,India-575025.
- 4 Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology,A Constituent Institute of Maniapal UniversityManiapal-576 119, Karnataka, India.,
Abstract
Nano particulate composites with Al-Si alloys (LM6 and LM25) as matrix and Multiwall Carbon Nanotube (MWNT) as reinforcement (0.25, 0.5, 0.75, 1.0 and 1.5 weight percentage) have been fabricated by powder metallurgy process. Damping specimens were prepared according to ASTM E 756-05 standard and the specimens were subjected to free vibration test to investigate the damping ratio and natural frequency. It is observed from the free vibration test data; both alloys (LM6 and LM25) have shown significant improvement in damping ratio, natural frequency and modulus when reinforced with 0.5 weight percentage of MWNT. Increase in weight percentage of MWNT beyond 0.5 leads to deterioration in damping ratio, natural frequency and modulus. This is due to agglomeration of reinforcement phase. The same has been observed in the morphological study using transmission electron microscopy (TEM). In this work an attempt has been made to also investigate the mechanical properties of the fabricated composites.
- Elwin L. Rooy, Aluminium Company of America, “Aluminium and Aluminium alloys”, ASME Handbook on Castings.
- S.C. Sharma, M. Krishna, A. Shashishankar, S. Paul Vizhian, “Damping behavior of aluminium/short glass fibre composites”, Materials Science and Engineering A364 (2004) 109–116.
- Chunlei Jia, “Study on damping behavior of FeAl3 reinforced commercial purity aluminium”, Materials and Design 28 (2007) 1711–1713.
- Lihua Liao, Xiuqing Zhang, Haowei Wang, Xianfeng Li, Naiheng Ma, “The characteristic of damping peak in Mg–9Al–Si Alloys”, Journal of Alloys and Compounds 429 (2007) 163–166.
- Advances in the metallurgy of aluminium, ASM International, www.asminternational.org
- Hennessey, C.H., Caley, W.F., Kipouros, G.J. and Bishop, D.P., “On Enhancing the Development of Al-Si Based Powder Metallurgy Alloys”, International Journal of Powder Metallurgy, 41(1) (2005) 50-63.
- G.B. Schaffer, “Powder Processed Aluminium Alloys”, Materials forum Vol.28 (2004) 65-74.
- C.C. Neubing, J. Gradl, H. Danninger, “Advances in Powder Metallurgy and Particulate Materials”, Part 13, Metal Powder Industries Federation (2002) 128–138.
- G. O’Donnell, L. Looney, “Production of aluminium matrix composite components using conventional PM technology”, Materials Science and Engineering A303 (2001) 292–301.
- F. Akhlaghi, S.A. Pelaseyyed, “Characterization of aluminum/graphite particulate composites synthesized using a novel method termed: in-situ powder metallurgy”, Materials Science and Engineering A 385 (2004) 258–266
- Zhen-kai Xie, Yasuo Yamada and Takumi Banno, “Mechanical Properties of Microporous Aluminum Fabricated by Powder Metallurgy”, Japanese Journal of Applied Physics Vol. 45, No. 32 (2006) 864–865
- D.P. Bishop, J.R. Cahoon, M.C. Chaturvedi, G.J. Kipouros, W.F. Caley, “On enhancing the mechanical properties of aluminum PM alloys”, Materials Science and Engineering A290 (2000) 16–24.
- Rupesh Khare, Suryasarathi Bose, “Carbon Nanotube Based Composites - A Review”, Journal of Minerals & Materials Characterization & Engineering, Vol. 4, No.1 (2005) 31-46
- Maksim Kireitseu, David Hui, Geoffrey Tomlinson, “Advanced shock-resistant and vibration damping of nano particle-reinforced composite material”, Composites Part B(2007)
- Deng chunfeng, Zhang xuexi, Ma yanxia, and Wang dezun, “Fabrication of aluminium matrix composite reinforced with carbon nanotubes”, Rare Metals, 26, No.5 (2007) 450-462.