The Development of Mathematical Model for the Prediction of Ageing Behaviour for Al-Cu-Mg/Bagasse Ash Particulate Composites
- 1 Department of Metallurgical and Materials Engineering,Ahmadu Bello University, Samaru, Zaria, Nigeria
- 2 Department of Metallurgical and Materials Engineering,Ahmadu Bello University, Samaru, Zaria, Nigeria
- 3 Department of Metallurgical and Materials Engineering,Ahmadu Bello University, Samaru, Zaria, Nigeria
- 4 Department of Metallurgical and Materials Engineering,Ahmadu Bello University, Samaru, Zaria, Nigeria
Abstract
The thermal ageing behaviour model of Al-Cu-Mg/Bagasse ash particulate composites with 2- 10wt% bagasse ash particles produced by double stir-casting method was developed in terms of weight fraction of bagasse ash, ageing temperature and time. Hardness values measurement was used in determining the ageing behaviour, after solution and age-hardened heat-treatment. The experimental results demonstrate that the bagasse ash was the major parameter in the ageing behaviour, followed by ageing temperature. The hardness values decreased as the ageing time increases, interaction of weight of bagasse ash, ageing time and ageing temperature. Moreover, the optimal combination of the testing parameters could be predicted. The predicted hardness values were found to lie close to that of the experimentally observed ones. The developed mathematical model can be employed for optimization of the process parameters of the ageing behaviour of Al-Cu-Mg/Bagasse ash particulate composites with respect to hardness values.
- V. S. Aigbodion and S. B. Hassan: Effect of Thermal Ageing Characteristics of Al-Si-Fe/SiC Particulate Composite Synthesized By Double Stir Casting, The Journal of Engineering Research(TJER), Vol. 7, No. 1, (2010) 53-61
- M. Sudarshan, K Surappa: Synthesis of fly ash particle reinforced A356 Al composites and their characterization, Materials Science and Engineering A, 480(2008)117–124.
- V.S. Aigbodion: Potential of using Bagasse ash particle in Metal Matrix Composite, PhD Work, Department of Metallurgical and Materials Engineering, Ahmadu Bello University, Samaru, Zaria, Nigeria (2010).
- J. Bienia, M. Walczak, B. Surowska., .J. Sobczaka: Microstructure and Corrosion Behaviour of Aluminum Fly Ash Composites, Journal of Optoelectronics and Advanced Materials Vol. 5, No. 2(2003)493 – 502.
- V.Kevorkijan, B. Utar, M. Torkar, G. Hiarmetta: Preparation of Al Based Composite Reinforced With Fine Dross Particles, ISSN 1318-0010 KZLTET(1998) 32(6)539.
- S. B. Hassan and V. S. Aigbodion: The study of the Microstructure and Interfacial Reaction of Al-Cu-Mg/Bagasse Ash Particulate Composite, Journal of Alloy & Compounds, 491 (2010) 571–574.
- S. Valdez, B. Campillo, R. Pérez, L. Martínez, H. García: Synthesis and microstructural characterization of Al–Mg alloy–SiC particle composite, Materials Letters 62(2008)2623–2625.
- S.B. Hassan, O. Aponbiede and V.S. Aigbodion: Precipitation hardening characteristics of Al- Si-Fe/SiC particulate composites Journal of alloys & compounds 466(2008), 268-272
- S. Suresh, T. Christman, Y. Sugimura, Accelerated aging in cast Al alloy—SiC particulate Composite, Scr. Metall. 23 (1989) 1599– 1602.
- P. Appendino, C. Badini, F. Marino, A. Tomasi, 6061 Aluminium alloy—SiC particulate Composite: a comparison between aging behaviour in T4 and T6 treatments, J. Mater. Sci. Eng. A.135 (1991) 275–279.
- L. Salvo, M. Svery, Effect of reinforcement on age-hardening of cast 6061-AlSiC and 6061 Al-Al 2 O 3 particulate composite, Metall. Trans. A 22A (1996) 2553–2653.
- Y. Sahin.: The prediction of wear resistance model for the metal matrix composites, Wear 258 (2005) 1717–1722.
- I. Miller, J.E. Freund: Probability and Statistics for Engineers, Prentice Hall India Ltd., India (2001), 125-140.