Potentials of Maize Stalk Ash as Reinforcement in Polyster Composites
- 1 Department of Metallurgical and Materials Engineering, Ahmadu Bello University,Zaria, Nigeria
- 2 Department of Metallurgical and Materials Engineering, Ahmadu Bello University,Zaria, Nigeria
- 3 Department of Metallurgical and Materials Engineering, Ahmadu Bello University,Zaria, Nigeria
Abstract
This paper examine the microstructure and the mechanical properties of maize stalk ash particles reinforced polyester composites with the aim of producing a composite material showing enhanced properties for engineering applications. Maize stalk ash particles (MSAp) were added in different volume fractions into a polyester matrix at 5, 10, 15 and 20% respectively. Composites samples were produced from these mixtures and the effect of the maize stalk ash content on the mechanical and microstructural properties of the composites was investigated and analyzed. Results from the scanning electron microscope (SEM) of the composites show a good and gradual interfacial bonding as the MSAp content increases while the Energy Dispersive spectrometer (EDS) and X-ray diffraction (XRD) show that carbon is present in the ash. The tensile strength, tensile modulus and compressive strength value increases as the maize stalk ash content increases but there is a gradual decrease for the impact strength. These results showed that the maize stalk ash can be used to improve the strength of polymer matrix composites for use in automobile and building applications.
- Bucknall, C.B. Rubber toughening. In: The Physics of Glassy Polymers. Chapman & Hall, London, 1997; pp. 363–412.
- Nakamura Y, Yamaguchi M, Okubo M, Matsumoto T. Effects of particle size on mechanical and impact properties of epoxy resin filled with spherical silica. J. Appl Polym Sci 1992; 45:1281–9.
- Mori T, Tanaka K. Average stress in matrix and average energy of materials with misfitting inclusions. Acta Metal 1973; 21: 571–4.
- Curtu and D. Motoc Luca. Theoretical and Experimental Approach of multiphase composite materials in DAAAM International Scientific Book , B. Katalinic, Ed. Vienna: DAAAM International Publishing, 2009, pp. 349-362.
- Tavman, I. H. Thermal and mechanical properties of aluminium powder-filled high density polyethylene composites. Journal of Applied Polymer Science, Vol. 62, 1996, pp. 2161-2167.
- Lombardo, N. Effect of an inhomogeneous interphase on the thermal expansion coefficient of particulate composite. Composites Science and Technology, Vol. 65, 2005, pp. 2118-2128.
- Wang M., Berry C., Braden M., and Bonfield W., (1998) Young’s and shear moduli of ceramic particle filled polyethylene. J Mater Sci Mater Med; 9: 621–4.
- Tjong S.C., and Xu S.A. (2001). Ternary polymer composites: PA6,6/maleated SEBS/glass beads. J Appl Polym Sci;81:3231–7.
- Amdouni N., Sautereau H., and Gerard J.F. (1992). Epoxy composites based on glass-beats: Mechanical-properties. J Appl Polym Sci;46: 1723–35.
- Munoz, A. Potential of Maize-Lime Pozzolana Coomposite to Develop low cost Housing Composite. Proceedings of NOCMAT, 2008. Cali Colombia.
- Amdouni N., Sautereau H., and Gerard J.F. Epoxy composites based on glass-beats: Mechanical-properties. J Appl Polym Sci;46: 1992; 1723–35.
- Ismail, H., Rozman, H. D., Jaffri R. M., and Mohd Ishak, Z. A. Oil Palm Wood Flour Reinforced Epoxidized Natural Rubber Composites: The effect of filler content and size,” Euro. Poly. J., 33, 10-12, 1997; pp. 1627-1632.
- Ou Y., Yang F., and Yu Z. A new conception on the toughness of nylon 6/silica nanocomposite prepared via in situ polymerization. J Polym Sci Part B Polym Phys;36: 1998; 789–95.
- Kendall K. Fracture of particulate filled polymers. Brit Polym J;10: 1987;35–8.
- Oghenevweta, E.J. The potential of using maize stalk ash as reinforcement in polymer matrix particulate composite, M.Sc on-going, Department of Metallurgical and Materials Engineering, Ahmadu Bello University, Zaria, Nigeria, 2011.