Dry Sliding Wear Behaviour of Aluminium/Be<sub>3</sub>Al<sub>2</sub>(SiO<sub>3</sub>)<sub>6</sub> Composite Using Taguchi Method
- 1 Research Scholar, Department of Mechanical Engineering, Sri Siddhartha Institute of Technology, Maralur Post, Tumkur-572105, Karnataka, India
- 2 Department of Mechanical Engineering, P.A. College of Engineering, Mangalore -574153, Karnataka, India
Abstract
The present study deals with investigation relating to the influence of wear parameters like sliding speed, applied load and sliding distance on the dry sliding wear of aluminium metal matrix composites. The design of experiment approach was employed to acquire data in controlled way using Taguchi method. A Pin-on-disc apparatus was used to conduct the dry sliding wear test. An orthogonal array, signal-to-noise ratio and analysis of variance were employed to investigate the wear behavior of aluminium and it’s composite. The mathematical model was obtained to determine the wear rate of the aluminium and it’s composite. The confirmation tests were conducted to verify the experimental results. The incorporation of Be 3 Al 2 (SiO 3 ) 6 as reinforcement material in aluminium matrix material improves the tribological characteristics.
- B.G.Park, A.G.Crosky and A.K.Hellier., Journal of material science 31, 1997, pp.1775-1788.
- T.S.Srivastava. Journal of material science, 31, 1996, pp.1375-1388.
- N. R. Prabhu Swamy, C. S. Ramesh and T. Chandrashekar, “Effect of Heat Treatment on Strength and Abrasive Wear Behaviour of Al6061–SiCp Composites”, Bull. Mater. Sci., Vol. 33, No. 1, 2010, pp.49–54.
- J.A.Hooker and P.J.Doorber, Material Science and Technology. 6 , 2000, pp. 725-731
- Sinclair I. and Gregson P.J., Mater. Sci Technol., vol. 3, 1997, 709.
- T.W.Clyne, “Metal Matrix Composites: Matrices and Processing”, A Mortensen (ed.), Elsevier, 2001.
- V.K.Lindroos and M.J.Talvitie, J. mater Proc. Tech, 53, 1995, pp. 273-278.
- Manoj Singla, D. Deepak Dwivedi, Lakhvir Singh and Vikas Chawla, “Development of Aluminium Based Silicon Carbide Particulate Metal Matrix Composite”, Journal of Minerals & Materials Characterization & Engineering, Vol.8, No.6, 2009, pp 455-467.
- A.P. Sannino and H,J. Rack, “Dry sliding wear of discontinuously reinforced aluminium composites: review and discussion”, Wear, 189, 1995, pp.1-19.
- Seteban Fernandez J, Model Rocio Fernandez, Vijande diaz R and Tucho Navarro R, “Abrasive Wear Analysis using Factorial Experimental Design”, Wear, Vol.255, 2003, pp. 38-43.
- Hemanth Kumar T R, Swamy R P and Chandra-shekar T K, “Tribological Studies on Discontinuously Reinforced Metal Matrix Composite using Design of Experiment”, journal of manufacturing engineering, Vol.6, Issue 2, 2011, pp. 106-110.
- Leisk G and Saigal, “A Statistical Approach to the Heat Treatment Optimization of Al-Al 2 O 3 Particulate Composite”, Journal of Materials Engineering and Performance, Vol. 1(1), 45, 1992.
- Roy K.R., A Primer on the Taguchi method, Van Nostrand Reinhold, New York, NY, 1990.
- Ross P.J., Taguchi technique for quality engineering, McGraw-Hill, New York, NY, 1993.
- Sahin Y., “The Prediction of Wear Resistance Model for the Metal Matrix Composites”, Wear, Vol. 258, Issues 11-12, 2005, pp. 1717-1722.
- Taguchi, G., Konishi and S., “Taguchi Methods Orthogonal Arrays and Linear Graphs: Tools for Quality Engineering”, American Supplier Institute, Dearborn, 1987.
- Taguchi, G., Taguchi on Robust Technology Development: Bringing Quality Engineering Upstream, ASME Press, New York, NY, 1993,