Assessment of Cutting Parameters Influencing on Thrust Force and Torque during Drilling Particulate Filled Glass Fabric Reinforced Epoxy Composites
- 1 Department of Mechanical Engineering, PES Institute of Technology and Management, Shivamogga, India
- 2 Department of Mechanical Engineering, The National Institute of Engineering, Mysore, India
- 3 Department of Mechanical Engineering, University B.D.T. College of Engineering, Davangere, India
- 4 Department of Mechanical Engineering, Don Bosco Institute of Technology, Bangalore, India
Abstract
Drilling is indispensable process and it cannot be avoided for joining composite structures used in various engineering applications. In this research article, the influence of drilling parameters on thrust force and torque of silica (SiO 2 ) and alumina (Al 2 O 3 ) filled into glass fabric reinforced epoxy (G-E) composites are analyzed. Drilling experiments are conducted on these composite materials using BATLIBOI make radial drilling machine. Two different drill bits (HSS and cemented carbide) are used for the experimentation. The influence of drilling parameters like cutting speed and feed on thrust force and torque on drilling of particulate filled G-E composites has been carried out. The experimental results indicated that the thrust force and torque were increased with increasing feed and cutting speed for all the composites tested. Further, it is observed that the carbide drill performed better than HSS drill during drilling of particulate filled G-E composites. The drilled surfaces are examined using scanning electron microscopy (SEM) and damage mechanisms are discussed.
- J. Mathew, N. Ramakrishnan and N. K. Naik, “Investigations into the Effect of Geometry of a Trepanning Tool on Thrust and Torque during Drilling of GFRP Composites,” Journal of Materials Processing Technology, Vol. 91, No. 1, 1999, pp. 1-11. doi:10.1016/S0924-0136(98)00416-6
- I. El-Sonbaty, U. A. Khashaba and T. Machaly, “Factors Affecting the Machinability of GFR/Epoxy Composites,” Composite Structures, Vol. 63, No. 3, 2004, pp. 329-338. doi:10.1016/S0263-8223(03)00181-8
- R. Zitoune, V. Krishnaraj and F. Collombet, “Study of Drilling of Composite Material and Aluminium Stack,” Composite Structures, Vol. 92, No. 5, 2008, pp. 1246- 1255.
- E. Capello and V. Tagliaferri, “Drilling Damage of GFRP and Residual Mechanical Behavior—Part I: Drilling Damage Generation,” Journal of Composites Technology and Research, Vol. 23, No. 2, 2001, pp. 122-130. doi:10.1520/CTR10920J
- S. Arul, L. Vijayaraghavan, S. K. Malhotra and R. Krishnamurthy, “The Effect of Vibratory Drilling on Hole Quality in Polymeric Composites,” International Journal of Machine Tools & Manufacture, Vol. 46, No. 3-4, 2006, pp. 252-259. doi:10.1016/j.ijmachtools.2005.05.023
- H. Hocheng and C. C. Tsao, “Analysis of Delamination in Drilling Composite Materials Using Core Drill,” Australian Journal of Mechanical Engineering, Vol. 1, No. 1, 2004, pp. 49-53.
- S. C. Lin and I. K. Chen, “Drilling Carbon Fiber-Rein- forced Composite Material at High Speed,” Wear, Vol. 194, No. 1-2, 1999, pp. 156-162. doi:10.1016/0043-1648(95)06831-7
- U. A. Khashaba, “Delamination in Drilling GFR—Thermoset Composites,” Composite Structures, Vol. 63, No. 3-4, 2004, pp. 313-327. doi:10.1016/S0263-8223(03)00180-6
- R. Piquet, B. Ferret, F. Lachaud and P. Swider, “Experimental Analysis of Drilling Damage in Thin Carbon/Epoxy Plate Using Special Drills,” Composites Part A, Vol. 31, No. 10, 2000, pp. 1107-1115. doi:10.1016/S1359-835X(00)00069-5
- V. Krishnaraj, S. Vijayarangan and A. Ramesh Kumar, “Effect of Drilling Parameters on Mechanical Strength in Drilling Glass Fiber Reinforced Plastic,” International Journal of Computer Applications in Technology, Vol. 28, No. 1, 2007, pp. 87-93. doi:10.1504/IJCAT.2007.012336
- A. M. Abrao, P. E. Faria, J. C. Campos Rubio, P. Reis and J. Paulo Davim, “Drilling of Fiber Reinforced Plastics: A Review,” Journal of Materials Processing Technology, Vol. 186, No. 1-3, 2007, pp. 1-7. doi:10.1016/j.jmatprotec.2006.11.146