Effect of Orientation and Applied Load on Abrasive Wear Property of Brass 60:40
- 1 Department of Mechanical Engineering, Integral University, Lucknow, India
- 2 Jahagirabad Institute of Technology, Jahangirabad, India
- 3 Sri Ram Swaroop Memorial Group of Professional College, Lucknow, India
Abstract
Wear is a continuous process in which material is degraded with every cycle. Scientists are busy in improving the wear resistance. Approximately 75% failure in components or machine parts is due to wear. The present paper investigates experimentally the effect of orientation and normal load on alloy of copper and zinc, i.e. Brass, and calculates weight loss due to wear. To do so, a multi-orientational pin-on-disc apparatus was designed and fabricated. Experiments were carried out under normal load 05-20 N, speed 2000 rpm. Results show that the with-increasing load weight loss increases at all angular positions. The loss in weight is maximum at zero degree (horizontal position) and minimum at ninety degree (vertical position) for a particular load. Maximum wear occurs when the test specimen is held at 0° angle and minimum wear occurs when the specimen is held at 90° angle for given applied load. The circumferential distance travel is constant for all positions and for all loads but still mass loss varies.
- J. F. Archard, “Wear Theory and Mechanisms,” In: M. B. Peterson and W. O. Winer, Eds., Wear Control Handbook, ASME, New York, 1980, pp. 35-80.
- D. Tabor, “Friction and Wear—Developments over the Last 50 Years, Keynote Address,” In: Proceedings of International Conference on Tribology—Friction, Lubrication and Wear, 50 Years On, Institution of Mechanical Engineers, London, 1987, pp. 157-172.
- S. T. Oktay and N. P. Suh, “Wear Debris Formation and Agglomeration,” ASME Journal of Tribology, Vol. 114, No. 2, 1992, pp. 379-393. http://dx.doi.org/10.1115/1.2920897
- N. Saka, M. J. Liou and N. P. Suh, “The Role of Tribology in Electrical Contact Phenomena,” Wear, Vol. 100, No. 1-3, 1984, pp. 77-105. http://dx.doi.org/10.1016/0043-1648(84)90007-3
- N. P. Suh and H. C. Sin, “On the Genesis of Friction and Its Effect on Wear,” In: H. S. Cheng and L. M. Keer, Eds., Solid Contact and Lubrication, AMD-Vol. 39, ASME, New York, 1980, pp. 167-183.
- V. Aronov, A. F. D’Souza, S. Kalpakjian and I. Shareef, “Experimental Investigation of the Effect of System Rigidity on Wear and Friction-Induced Vibrations,” ASME Journal of Lubrication Technology, Vol. 105, No. 2, 1983, pp. 206-211. http://dx.doi.org/10.1115/1.3254566
- V. Aronov, A. F. D’Souza, S. Kalpakjian and I. Shareef, “Interactions among Friction, Wear, and System Stiffness—Part 1: Effect of Normal Load and System Stiffness,” ASME Journal of Tribology, Vol. 106, No. 1, 1984, pp. 54-58. http://dx.doi.org/10.1115/1.3260867
- V. Aronov, A. F. D’Souza, S. Kalpakjian and I. Shareef, “Interactions among Friction, Wear, and System Stiffness—Part 2: Vibrations Induced by Dry Friction,” ASME Journal of Tribology, Vol. 106, No. 1, 1984, pp. 59-64. http://dx.doi.org/10.1115/1.3260868
- V. Aronov, A. F. D’Souza, S. Kalpakjian and I. Shareef, “Interactions among Friction, Wear, and System Stiffness—Part 3: Wear Model,” ASME Journal of Tribology, Vol. 106, No. 1, 1984, pp. 65-69. http://dx.doi.org/10.1115/1.3260869
- J. W. Lin and M. D. Bryant, “Reduction in Wear Rate of Carbon Samples Sliding against Wavy Copper Surfaces,” ASME Journal of Tribology, Vol. 118, No. 1, 1996, pp. 116-124. http://dx.doi.org/10.1115/1.2837065
- M. A. Chowdhury, M. K. Khalil, D. M. Nuruzzaman and M. L. Rahaman, “The Effect of Sliding Speed and Normal Load on Friction and Wear Property of Aluminum,” International Journal of Mechanical & Mechatronics Engineering IJMME-IJENS, Vol. 11, No. 1, 2011, pp. 45- 9.