Particle size analysis, Atterberg limits, X-ray diffraction, X-ray fluorescence and firing tests were used to determine physico-chemical, mineralogical and technological characteristics of residual lateritic (K1M, Ma2) and alluvial (KB3, KG3) clays from Foumban (West-Cameroon). For technological properties, the samples were pressed and fired over a temperature range of 900 ° C - 1200 ° C to determine the open porosity, linear shrinkage, bulk density and compressive strength. Kaolinite (31% - 65%) and quartz (35% - 50%) are dominant in Foumban clays with accessory K-feldspar, plagioclase, illite, smectite, rutile, and goethite. But their proportion changes from one sample to another, having a significant effect on the behaviour of the clay materials: highest proportion of quartz (50%) in sample K1M; relative high feldspars (20%) and illite contents (10%) in KB3 and MA2; high smectite content in KG3 (up to 20%). Chemical analyses indicate high SiO2 (49% - 77%) and low Al2O3 (14% - 23%) contents in the four samples, with comparatively low contents of iron oxides (4% - 7% in samples KB3 and KG3, 2.5% in MA2 and ~1.5% in sample K1M). The particle size distribution of the alluvial clays (KG3 and KB3) differs considerably: 7% to 37% of clay fraction, 20% to 78% of silt, and 15% to 58% of sand, while residual clays (K1M and MA2) present on average 12% of clay, 51% of silt and 37% of sand. Two raw clays (KB3 and MA2) can be used for bricks/tiles production without beneficiation or addition. K1M requires some flux addition to decrease the sintering temperature while KG3 presents poor properties due to the combined occurrence of smectite and a high clayey fraction (37%). Such mineralogical composition is responsible for very high plasticity (PI: 50), high shrinkage (LS: 5% - 16%), low porosity (OP: up to 21%) and high flexural strength (FS: 16 - 23 N/mm2) above 1050 ° C. This last clay is therefore less appropriate for bricks and roofing tiles production since degreasers must be added to the raw material.
Reeves, G.M., Sims, I. and Cripps, J.C. (2006) Brick and Other Ceramic Products. In: Reeves, G.M., Sims, I. and Cripps, J.C., Eds., Clay Materials Used in Construction, Geological Society, Engineering Geology Special Publication, London, No. 21, 400-425.
Manning, D.A.C. (1995) Introduction to Industrial Mineral. Chapman and Hall Edition, London. https://doi.org/10.1007/978-94-011-1242-0
Vieira, C.M.F. and Sanchez Monteiro, R.S.N. (2008) Characteristics of Clays and Properties of Building Ceramics in the State of Rio de Janeiro, Brazil. Construction and Building Materials, 22, 781-787. https://doi.org/10.1016/j.conbuildmat.2007.01.006
Mefire, A.N., Njoya, A., Fouateu, R.Y., Nsandamoun, A.T., Nzeugang, A.N., Mache, J.R., Chinje, U.M., Pilate, P., Flament, P., Siniapkine, S., Ngono, A. and Fagel, N. (2015) Kaolin Occurrence in Koutaba (West-Cameroon): Mineralogical and Physicochemical Characterization for Ceramic Products. Clay Minerals, 50, 593-606. https://doi.org/10.1180/claymin.2015.050.5.04
Weecksteen, G. (1957) Carte géologique de reconnaissance au 1/500000, feuille Douala-Est avec notice explicative. Direction Mines Géologie, Cameroun.
Moundi, A., Wandji, P., Ghogomu, R.T., Bardintzeff, J.M., Njilah, I.K., Foumboure, I. and Ntieche, B. (2009) Existence of Quaternary Ankaramites among Tertiary Floods Basalts at Koutaba (Bamoun Plateau, Western Cameroon): Petrology and Isotope Data. Review of the Bulgarian Geological Society, 70, 115-124.
Moore, D. and Reynolds Jr., R.C. (1997) X-Ray Diffraction and the Identification and Analysis of Clay Minerals. Oxford University Press, Oxford.
Cook, H.E., Johnson, P.D., Matti, J.C. and Zemmels, I. (1975) Methods of Sample Preparation and X-Ray Diffraction. Data Analysis, X-Ray Mineralogy Laboratory, Deep Sea Drilling Project, University of California, Riverside. Contribution No. 74-5, 999-1007. https://doi.org/10.2973/dsdp.proc.28.app4.1975
Boski, J., Pessoa, P., Pedro, J., Thorez, J.M., Dias, A. and Hall, I.R. (1998) Factors Governing Abundance of Hydrolysable Amino Acids in the Sediments from the N.W. European, Continental Margin (47-50°N). Progress Oceanography, 42, 145-164. https://doi.org/10.1016/S0079-6611(98)00032-9
Fagel, N., Boski, T., Likhoshway, L. and Oberhaensli, H. (2003) Late Quaternary Clay Mineral Record in Central Lake Baikal (Academician Ridge, Siberia). Paleogeography, Paleoclimatology, Paleoecology, 193, 159-179. https://doi.org/10.1016/S0031-0182(02)00633-8
Kahle, M., Kleber, M. and Reinnold, J. (2002) Review of XRD-Based Quantitative Analyses of Clay Minerals in Soils. Geoderma, 109, 197-205. https://doi.org/10.1016/S0016-7061(02)00175-1
Biscaye, P.E. (1965) Mineralogy and Sedimentation of Recent Deep-Sea Clay in the Atlantic Ocean and Adjacent Seas and Oceans. Geological Society of America Bulletin, 76, 803-832. https://doi.org/10.1130/0016-7606(1965)76[803:MASORD]2.0.CO;2
ASTM-America Society for Testing Materials (1998) Standard Test Method for Particle-Size Analysis of Soils, ASTM D-422-63.
ASTM-America Society for Testing Materials (2000) Standard Test Method for Liquid Limit, Plastic Limit, and Plasticity Index of Soils, ASTM D, 14.
Gonzalez-Garcia, F., Romero-Acosta, V., Garcia-Ramos, G. and Gonzalez-Rodriguez, M. (1990) Firing Transformations of Mixtures of Clays Containing Illite, Kaolinite and Calcium Carbonate Used by Ornamental Tile Industries. Applied Clay Science, 5, 361-375. https://doi.org/10.1016/0169-1317(90)90031-J
Carretero, M.I., Dondi, M., Fabbri, B. and Raimondo, M. (2002) The Influence of Shaping and Firing Technology on Ceramic Properties of Calcareous and Non-Calcareous Illitic-Chloritic Clays. Applied Clay Science, 20, 301-306. https://doi.org/10.1016/S0169-1317(01)00076-X
ASTM-America Society for Testing Materials (2002) Standard Test Method for Compressive (Crushing) Strength of Fired Whitewares Materials, ASTM C773-88. Annual Book of Products, ASTM C373-88, Annual Book of ASTM standard.
ASTM-America Society for Testing Materials (2002) ASTM Standard Test Method for Water Absorption, Bulk Density, Apparent Density and Apparent Specific. Gravity of Fired Whitewares Standard.
Velde, B. and Meunier, A. (2008) The Origin of Clays Minerals in Soils and Weathered Rocks. Springer Verlag, Berlin and Heidelberg. https://doi.org/10.1007/978-3-540-75634-7
Dondi, M., Iglesias, C., Dominguez, E., Guarini, G. and Raimondo, M. (2008) The Effect of Kaolin Properties on Their Behaviour in Ceramic Processing as Illustrated by Range of Kaolins from the Santa Cruz and Chubut Provinces, Patagonia (Argentina). Applied Clay Science, 40, 143-158. https://doi.org/10.1016/j.clay.2007.07.003
Kornmann, M. (2005) Ingénieurs du Centre Technique des Tuiles et Briques, Matériaux de construction en terre cuite, fabrication et proprieties. Editions Septima, Paris, 33-34.
Oikonomopoulod, K.I., Perraki, M., Tougiannidis, N. and Perraki, T. (2015) Clays from Neogene Achlada Lignite Deposits in Florina Basin (Western Macedonia, N. Greece): A Prospective Resource for the Ceramic Industry. Applied Clay Science, 103, 1-9. https://doi.org/10.1016/j.clay.2014.11.002
.Ngun, B.K., Mohamad, H., Sulaiman, S.K., Okada, K. and Ahmad, Z.A. (2011) Some Ceramic Properties of Clays from Central Cambodia. Applied Clay Science, 53, 33-41. https://doi.org/10.1016/j.clay.2011.04.017
McNally, G.H. (1998) Soil and Rock Construction Materials. CRC Press, London, 291-310. https://doi.org/10.4324/9780203476574
Leonards, G.A. (1968) Predicting Settlement of Buildings on Clay Soils. Proceedings of Soil Mechanics Lecture Series on Foundation Engineering, Illinois Section of ASCE and Northwestern University, Evanston, Il, 41-50.
Casagrande, A. (1948) Classification and Identification of Soils. Transactions of the American Society of Civil Engineers, 113, 901-930.
Nzeukou, A., Kamgang, V., Medjo, R., Melo, U., Njoya, A., Lemougna, P. and Fagel, N. (2013) Industrial Potentiality of Alluvial Clays Deposits from Cameroon: Influence of Lateritic Clayey Admixture for Fired Bricks Production. Journal of Minerals and Materials Characterization and Engineering, 1, 236-244. https://doi.org/10.4236/jmmce.2013.15037
Manoharan, C., Sutharsan, P., Dhanapandian, S., Venkatachalapathy, R. and Mohamed Asanull, R. (2011) Analysis of Tem-perature Effect on Ceramic Brick Production from Alluvial Deposits, Tamilnadu, India. Applied Clay Science, 54, 20-25. https://doi.org/10.1016/j.clay.2011.07.002
Souza, G.P., Sanchez, R. and de Holanda J.N. (2002) Characteristics and Physical-Mechanical Properties of fired Kaolinitic Materials. Ceramica, 48, 102-107. https://doi.org/10.1590/S0366-69132002000200009
Bain, J.A. and Highley, D.E. (1978) Regional Appraisal of Clay Resources. A Challenge to the Clay Mineralogist. Proceedings of the IV International Clay Conference AIPEA, Oxford, 10-14 July 1978, 437-458.