Design a Collector with More Reliability against Defects during Manufacturing in Nanometer Technology, QCA
- 1 Computer Engineering Department, Sadjad University, Mashhad, Iran
- 2 Computer Engineering Department, Shahid Beheshti University, Tehran, Iran
- 3 Electrical Engineering Faculty, Sahand University of Technology, Sahand, Iran
Abstract
Nowadays Quantum Cellular Automata (QCA) as the leading technology in design of microelectronic systems has been raised. With respect to high velocity and density in low power and also simple concepts, this technology is a viable al ternative to CMOS technology. In collector design, the primary component of each processor is very important. Due to the small elements in this technology, failure rate in manufacturing process technology is very high. In the other hand, the simulation shows that the intersection point of two wires is one of the critical points in QCA circuits. This means that defect s in the manufacturing process around these points can cause malfunction in the circuit performance. In this paper , a collector in cross sections of wire in his new method used higher reliability against defects during manufactur ing has been developed. QCA Designer software is used to simulate the case study system.
- T. J. Dysart and P. M. Kogge, “System Reliabilities When Using Triple Modular Redundancy in Quantum-Dot Cellular Automata,” Proceeding of the 23rd IEEE International Symposium on Defect and Fault Tolerance of VLSI System, Boston, 1-3 October 2008, pp. 72-80.
- C. S. Lent, P. D. Tougaw and W. Porod, “B Saturation in Coupled Quantum Dots for Quantum Cellular Automata,” Applied Physics Letters, Vol. 62, No. 7, 1993, pp. 714-716.
- P. D. Tougaw and C. S. Lent, “Logical Devices Implemented Using Quantum Cellular Automata,” Journal of Applied Physics, Vol. 75, No. 3, 1994, pp. 1818-1825.
- C. G. Smith, “Computation without Current,” Science, Vol. 284, No. 5412, 1999, pp. 274-284. doi:10.1126/science.284.5412.274
- P. D. Tougaw and C. S. Lent, “Dynamic Behavior of Quantum Cellular Automata,” Journal of Applied Physics, Vol. 80, No. 8, 1996, pp. 4722-4735. doi:10.1063/1.363455
- P. D. Tougaw, C. S. Lent and W. Porod, “Bistable Saturation in Coupled Quantum-Dot Cells,” Journal of Applied Physics, Vol. 74, No. 5, 1993, pp. 3558-3565. doi:10.1063/1.354535
- K. Hennessy and C. S. Lent, “Clocking of Molecular Quantum-Dot Cellular Automata,” Journal of Vacuum Science and Technology B, Vol. 19, No. 5, 2001, pp. 1752-1755.
- C. S. Lent and B. Lsaksen, “Clocked Molecular Quantum-Dot Cellular Automata,” IEEE Transaction on Electron Devices, Vol. 50, No. 9, 2003, pp. 1890-1895. doi:10.1109/TED.2003.815857
- M. B. Tahoori, M. J. Huang and F. Lombardi, “Defects and Faults in Quantum Cellular Automata at Nano Scale,” Proceeding of the 22nd IEEE VLSI Test Symposium (VTS), Napa Valley, 25-29 April 2004, pp. 291-296.
- W. Wang, K. Walus and G. A. Jullien, “Quantum Dot Cellular Automata Adders,” Proceeding of 3rd IEEE Nano Conference, San Francisco, 12-14 August 2003, pp. 461-464.
- A. Vetteth, K. Walus, V. S. Dimitrov and G. A. Jullien, “Quantum-Dot Cellular Automata Carry-Look-Ahead Adder and Barrel Shifter,” Proceedings of the IEEE Emerging Telecommunications Technologies Conference, Dallas, 23-24 September 2002.
- M. T. Niemier, “Designing Digital Systems in Quantum Cellular Automata,” Master’s Thesis, University of Notre Dame, Indiana, 2004.
- H. Cho and E. E. Swartzlander, “Adder Design and Anaysis for Quantum-Dot Cellular Automata,” IEEE Transaction on Nanotechnology, Vol. 6, No. 3, 2007 pp. 374-383.