Optimization of Welding Parameters for Friction Stir Lap Welding of AA6061-T6 Alloy
- 1 Department of Mechanical Engineering, Anna University, Chennai, India
- 2 Department of Mechanical Engineering, Anna University, Chennai, India
- 3 Department of Mechanical Engineering, Anna University, Chennai, India
- 4 Department of Mechanical Engineering, Anna University, Chennai, India
Abstract
Friction Stir Welding (FSW) is currently used in many aircraft and aerospace sheet metal structures involving lap joints and there has been growing interest in recent years in utilizing this process for joining aluminum alloys. In this paper, Friction Stir Lap Welding (FSLW) of the 6061 - T6 aluminum alloy was carried out to obtain the optimum welding condition for maximum shear strength where the rotational speed, axial load, and welding speed were taken as process parameters. An L-9 orthogonal array, a Taguchi Method with consideration of three levels and three factors was designed and executed for conducting trials. Analysis of variance (ANOVA) and Signal to Noise (S/N) ratio were employed to investigate the influence of different welding parameters on the shear strength and obtain the optimum parameters. The Fisher-Test was also implemented to find the design parameter which had the most important effect on the characteristic of quality. The results indicated that the tool rotational speed had the maximum percentage contribution (51%) on the response (shear strength) followed by the welding speed (38%) and the axial load (8%) while the percentage of error was 3%. However, to confirm the main effects for the means and S/N ratios of the experiment, theoretical shear strength values were computed to predict the tensile strength. The maximum shear strength of 60 MPa was achieved and the effectiveness of the method was confirmed. The optimum parameter combinations that provided higher shear strength were: rotational speed of 1200 rpm, welding speed of 45 mm/min and the axial load of 11.5 kN.
- Thomas, W.M., Nicholas, E.D., Needham, J.C., Murch, M.G., Templesmith, P. and Dawes, C.J. (1991) International Patent Application No. PCT/GB92/02203 and GB Patent Application No. 9125978.8.
- Mishra, R.S. and Ma, Z.Y. (2005) Friction Stir Welding and Processing. Materials Science and Engineering: R: Reports, 50, 1-78. https://doi.org/10.1016/j.mser.2005.07.001
- Liu, G., Murr, L.E., Niou, C.S., McClure, J.C. and Vega, F.R. (1997) Microstructural Aspects of the Friction-Stir Welding of 6061-T6 Aluminum. Scripta Materialia, 37, 355-361. https://doi.org/10.1016/S1359-6462(97)00093-6
- Rathinasuriyan, C., Kumar, V.S. and Shanbhag, A.G. (2014) Radiography and Corrosion Analysis of Sub-Merged Friction Stir Welding of AA6061-T6 Alloy. Procedia Engineering, 97, 810-818. https://doi.org/10.1016/j.proeng.2014.12.355
- Sankar, R., Rathinasuriyan, C. and Senthil Kumar, V.S. (2017) Effect of Cooling Conditions on Mechanical and Microstructural Behaviours of Friction Stir Processed AZ31B Mg Alloy. Modern Mechanical Engineering, 7, 144-160. https://doi.org/10.4236/mme.2017.74010
- Irving, B. (1997) Why Aren’t Airplanes Welded? Welding Journal, 76, 31-41.
- Thornton, P.H., Krause, A.R. and Davies, R.G. (1996) Aluminum Spot Weld. Welding Journal, 75, 101s.
- Dubourg, L., Merati, A. and Jahazi, M. (2010) Process Optimisation and Mechanical Properties of Friction Stir Lap Welds of 7075-T6 Stringers on 2024-T3 Skin. Materials & Design, 31, 3324-3330. https://doi.org/10.1016/j.matdes.2010.02.002
- Chen, Y.C. and Nakata, K. (2008) Friction Stir Lap Joining Aluminum and Magnesium Alloys. Scripta Materialia, 58, 433-436. https://doi.org/10.1016/j.scriptamat.2007.10.033
- Cao, X. and Jahazi, M. (2011) Effect of Tool Rotational Speed and Probe Length on Lap Joint Quality of a Friction Stir Welded Magnesium Alloy. Materials & Design, 32, 1-11. https://doi.org/10.1016/j.matdes.2010.06.048
- Saeid, T., Abdollah-Zadeh, A. and Sazgari, B. (2010) Weldability and Mechanical Properties of Dissimilar Aluminum-Copper Lap Joints Made by Friction Stir Welding. Journal of Alloys and Compounds, 490, 652-655. https://doi.org/10.1016/j.jallcom.2009.10.127
- Abdollah-Zadeh, A., Saeid, T. and Sazgari, B. (2008) Microstructural and Mechanical Properties of Friction Stir Welded Aluminum/Copper Lap Joints. Journal of alloys and Compounds, 460, 535-538. https://doi.org/10.1016/j.jallcom.2007.06.009