Effects of Fillerwire Composition along with Different Pre- and Post-Heat Treatment on Mechanical Properties of AISI 4130 Welded by the GTAW Process
- 1
- 2
- 3
Abstract
This research intends to find out the optimal mechanical properties of AISI 4130 steel welded by the GTAW process. Six test plates were joined by two types of filler wire with similar chemical composition to the base metal, and with lower carbon content and slightly higher alloy elements content compared to the first one. Test plates then exerted three different pre-heat and post-heat treatments on both groups. The three types of heat treatments were alternatively without pre-heat and post-heat, with pre-heat only, and finally with pre-heat and post-heat. Tensile, side bends and impact tests (for weld zone and HAZ) have been conducted. Results show that using low-carbon filler wire along with pre- and post-heat resulted in outstanding mechanical properties.
- W. E. Lukens, “Mechanical Properties of HSLA Steel Buried GTAW,” Proceedings of 67th AWS Conference, Atlanta, 1987, pp. 215S-220S.
- Lorentz, “Utilization of Quenching and Tempering of HS- LA in Heavy Thickness for Welded Construction,” Wel- ding Research Supplement, Vol. 5, No. 1, 1962, pp. 433S- 444S.
- T. Bevis and A. Weyenberg, “Best Practice for GTAW 4130 Chrom-Moly,” Welding Journal, Vol. 89, No. 4, April 2010, pp. 42-49.
- J. A. Todd, L. Chen, E. Y. Yankov and S. Mostovoy, “Crack Closure Effects on Fatigue Crack Growth Thresh-olds and Remaining Life in an HSLA Steel,” Journal of Pressure Vessel Technology, Transactions of the ASME, Vol. 119, No. 1, 1999, pp. 37-44.
- J. Fulcer and J. Fogle, “Choose the Correct Filler Rod and Establish a Weld Pool,” Welding Journal, Vol. 86 ,No. 8, 2007, pp. 38-40.
- L. P. Earolino, “The Effect of Carbon Content on the Need to Post Weld Heat Treat Low Alloy Steel Casting,” Welding Research Supplement, Vol. 5, No. 1, 1986, pp. 41-46.
- W. S. Kyte, “Post Weld Heat Treatment for Hydrogen Removal,” Welding Research Supplement, Vol. 2, No. 2, 1979, pp. 54S-58S.
- J. W. Hooijmians, “A Model of Hydrogen Absorption du- ring GTA Welding,” Welding Research Supplement, Vol. 9, No. 5, 1997, pp. 264S-268S.
- J. R. Still, “Welding of 4130, 4140, Steels for Drilling Sys- tems,” Welding Journal, Vol. 23, No. 2, 1997, pp. 37- 41.
- L. W. Tsay, Y. M. Li, C. Chen and S. W. Cheng, “Me- chanical Properties and Fatigue Crack Growth Rate of Laser Welded,” Journal of Fatigue, Vol. 14, No. 4, 1992, pp. 239-247.
- S. Ravi, V. Balasubramanian and N. Nemat, “Influence of Post Weld Heat Treatment on Fatigue Life Prediction of Strength Mismatched HSLA Steel Welds,” Journal of Fatigue, Vol. 27, No. 5, May 2005, pp. 547-553.
- H. Bultel and J. Vogt, “Influence of Heat Treatment on Fatigue Behavior of 4130 AISI Steel,” Journal of Fatigue, Vol. 2, No. 1, 2010, pp. 917-924.
- P. Macelino and H. Voorwald, “Considerations about the Welding Repair Effects on the Structural Integrity of an Airframe Critical to the Flight-Safety,” Journal of Fa- tigue, Vol. 2, No. 1, 2010, pp. 1895-1903.
- O. M. Akselen, “Assessment and Predications of HAZ Tensile Properties of HSLA,” Welding Research Suppl- ement, Vol. 7, No. 3, 1989, pp. 362S-365S.