A Qualitative Study of the Influence of Grooved Mold Surface Topography on the Formation of Surface Marks on As-Cast Ingots of Aluminum Alloy 3003 — Oak Academic Publishing
Research ArticleOpen AccessGoogle Scholar indexed
A Qualitative Study of the Influence of Grooved Mold Surface Topography on the Formation of Surface Marks on As-Cast Ingots of Aluminum Alloy 3003
School of Engineering, Grand Valley State University, Allendale, USA
1 School of Engineering, Grand Valley State University, Allendale, USA
The effects of the wavelength and orientation of machined grooves on a mold surface, casting speed, and melt superheat on the formation of surface marks on as-cast ingots were studied with an immersion casting tester and copper mold chill blocks. The mold surface topographies included a polished smooth surface, and those with machined unidirectional parallel contoured grooves oriented either parallel (vertical) or perpendicular (horizontal) to the casting direction. The unidirectional grooves were 0.232 mm deep with wavelength or spacing between 1 and 15 mm. The casting speed and melt superheat were between 1 and 200 mm/s, and 10 and 50 K, respectively. Two primary types of surface marks were observed on ingots cast with the copper mold with smooth surface topography, namely the finer and closely spaced ripples (Type I), and the widely spaced but coarser laps (Type II). The latter were more prevalent at the higher casting speeds and melt superheats. Qualitatively, formation of both types of surface marks on the as-cast ingots of the aluminum alloy 3003 appeared to be alleviated by increase in casting speed and melt superheat, and by the use of molds with grooved surface topography. In fact, casting with a mold surface with 1 mm spaced grooves that are perpendicular to the casting direction eliminated the formation of surface marks at casting speeds greater than 1 mm/s. It also improved the uniformity of the ingot subsurface microstructure and eliminated the associated subsurface segregation.
Emley, E. (1976) Continuous Casting of Aluminum. International Metals Review, 6, 75-115. https://doi.org/10.1179/imtr.1976.21.1.75
Buxmann, K. (1978) Surface Faults in Aluminum Continuous Casting. Aluminum, 54, 685-690.
Nofal, A. (1992) Surface Defect Formation in the DC-Cast Aluminum Products. Proceedings of Advances in Continuous Casting Research & Technology, Cairo, 13-15 April 1992, 205-218.
Anyalebechi, P.N. (2004) Technical Issues Impeding the Proliferation of Continuous Casting Processes in the Aluminum Industry. In: Schlesinger, M.E., Ed., EPD Congress 2004, The Minerals, Metals, and Materials Society, Pittsburgh, 191-215.
Gjonnes, L. (1996) Development of Surface Topography during Cold Rolling of Twin-Roll Cast Aluminum. Wear, 192, 216-227. https://doi.org/10.1016/0043-1648(95)06809-0
McCubbin, J.G. (1975) Inverse Solidification—A Theory of the Formation of the Surface Segregation on D.C. Cast Round Ingot. Light Metals, 2, 137-159.
Vosskuhler, H.Z. (1965) Inverse Segregation in Ingots of Nonferrous Metals. Metallkde, 56, 719-729.
Ackermann, P., Heinemann, W. and Kurz, W. (1984) Surface Quality and Meniscus Solidification of Pure Chill Cast Metals. Archiv für das Eisenhüttenwesen, 55, 1-8. https://doi.org/10.1002/srin.198405298
Saucedo, I., Beech, J. and Davies, G.J. (1982) Influence of Meniscus Freezing on Surface Defect Formation in Cast Products. In: Solidification in the Foundry and Cast House, The Metals Society, London, 461-468.
Collins, D.W.L. (1967) New Explanation of the Surface Structure of D.C. Ingots. Metallurgia, 137, 137-144.
Bergmann, W.J. (1970) Solidification in Continuous Casting of Aluminum. Metallurgical Transactions, 1, 3361-3364.
Nussbaum, A.I. (1995) Two State of the Art Ingot Scalping Installations. Light Metal Age, 10, 10-12.
Weckman, D.C. and Niessen, P. (1984) The Mechanism of Cold Shut Formation on D.C. Continuously Cast Non-Ferrous Alloy Products. Zeitschrift für Metallkunde, 75, 414-422.
Weckman, D.C. (1987) Horizontal Direct-Chill Continuous Casting of Non-Ferrous Alloy Rods. Zeitschrift für Metallkunde, 78, 880-886.
Quaresma, J.M. and Garcia, A. (1983) Analysis of the Factors Influencing the Formation of Surface Defects on Ingots. Proceedings of 38th Annual Congress ABM, Vol. 4, 303-324.
Quaresma, J.M.V., Cheung, N. and Garcia, A. (2007) The Effect of Solidification Thermal Variables on Surface Quality of Al-Cu Ingots. Journal of Alloys and Compounds, 428, 130-138. https://doi.org/10.1016/j.jallcom.2006.03.054
Malinovskii, R.R. (1987) Causes of Wrinkles Formation in Continuous Casting of Aluminum Alloys. Tsvetnye Metally/Non-Ferrous Metals, 90, 74-76.
Saucedo, I., Beech, J. and Davies, G.J. (1979) The Development of Surfaces in Steel Ingots and Strands. In: Proceedings of 6th Vacuum Metallurgy Conference on Special Melting, American Vacuum Society, New York, 885-905.
Benum, S., Hakonsen, A., Hafsa, J.E. and Sivertsen, J. (1999) Mechanisms of Surface Formation during Direct Chill (DC) Casting of Extrusion Ingots. In: Eckert, C.E., Ed., Light Metals 1999, The Minerals, Metals & Materials Society, Pittsburgh, 737-742.
Tomono, H., Kurz, W. and Heinemann, W. (1981) The Liquid Steel Meniscus in Molds and Its Relevance to the Surface Quality of Castings. Metallurgical Transactions B, 12, 409-411. https://doi.org/10.1007/BF02654475
Wray, P.L. (1981) Geometric Features of Chill-Cast Surfaces. Metallurgical Transactions B, 12, 167-176. https://doi.org/10.1007/BF02674770
Stemple, D.K., Zulueta, E.N. and Flemings, M.C. (1982) Effect of Wave Motion on Chill Cast Surfaces. Metallurgical Transactions B, 13, 503-509. https://doi.org/10.1007/BF02667767
Jacobi, H. and Schwerdtfeger, K. (2013) Ripple Marks on Cast Steel Surfaces. ISIJ International, 53, 1180-1186. https://doi.org/10.2355/isijinternational.53.1180
Thornton, D.R. (1956) An Investigation on the Function of Ingot Mould Dressings. The Journal of the Iron and Steel Institute, 300-315.
Suzuiki, M. and Yamaoka, Y. (2003) Influence of Carbon Content on Solidifying Shell Growth of Carbon Steels at the Initial Stage of Solidification. Materials Transactions, 44, 836-844.
Tomono, H., Ackermann, P., Kurz, W. and Heinemann, W. (1980) Elements of Surface Marks in the Continuous Casting of Steel. In: Conference Proceeding, Solidification Technology in the Foundry and Cast House, Warrick University, Coventry, 524-531.
Bouchard, D., et al. (2001) Effects of Substrate Surface Conditions on Heat Transfer and Shell Morphology in Solidification of a Copper Alloy. Metallurgical and Materials Transactions B, 32, 111-118. https://doi.org/10.1007/s11663-001-0013-y
Bouchard, D., et al. (2002) Control of Heat Transfer and Growth Uniformity of Solidifying Copper Shells through Substrate Temperature. Metallurgical and Materials Transactions B, 33, 403-411. https://doi.org/10.1007/s11663-002-0052-z
Irman, R. (1952) Continuous Casting of Aluminum in a Grooved Mold. Giesserei, 6-8, 393-394.
Buxmann, K., Bolliger, L.M. and Gyongyos, I. (1981) Mould with Roughened Surface for Casting Metals. US Patent No. 4,250,950.
Mizikar, E.A., Wojcik, W.M. and Li, K. (1967) U.S. Letters Patent No. 3,345,738.
Sugitani, Y., et al. (1985) Effect of the Mould Surface Conditions on Uneven Solidification and Heat Removal Rate through the Mould. Transactions of the Iron and Steel Institute of Japan, 25, B-91.
Nakai, K., et al. (1985) Improvement of Surface Quality of Continuously Cast Slab by Reducing Heat Flux Density in Mould. Proceedings of Shanghai Symposium on Continuous Casting, Shanghai, December 1985, 71.1-71.8.
Murakami, H., et al. (1992) Control of Uneven Solidified Shell Formation of Hypoperitectic Carbon Steels in Continuous Casting Mould. Journal—The Iron and Steel Institute of Japan, 8, 105-112.
Gaspar, T. (1987) U.S. Letter Patent No. 4,705,095.
Bartlett, E., Maringer, R. and Rayment, J. (1989) U.S. Letter Patent No. 4,865,117.
Nakada, M., et al. (1990) Canadian Patent Application No. 2,000,618.
Tanaka, S., et al. (1988) European Patent Application No. 0309247A2.
Weirauch, D.A. and Giron, A. (1999) The Early Stages of Aluminum Solidification in the Presence of a Moving Meniscus. In: Zabaras, N., et al., Eds., Proceedings of a Conference on the Integration of Material, Process, and Product Design, Balkema, Rotterdam, 183-191.
Weirauch, D.A., et al. (2000) Laboratory Study of Cast Surface Structure Evolution I: Mold-Contact Stage. In: Peterson, R.D., Ed., Light Metals 2000, The Minerals, Metals, and Materials Society, Pittsburgh, 649-656.
Morishita, M., Nakayama, K., Tokuda, K. and Yoshikawa, K. (2000) Laboratory Study of Cast Surface Structure Evolution II—Macro Air Gap Stage. In: Peterson, R.D., Ed., Light Metals 2000, The Minerals, Metals, and Materials Society, Pittsburgh, 657-662.
Hunter, N.S., et al. (1999) The Influence of Mould Metallurgy on Surface Defects in Peritectic Carbon and Austenitic Stainless Steels. La Revue Metallurgie Cahiers D’Informations Techniques, 96, 473-482. https://doi.org/10.1051/metal/199996040473
Anyalebechi, P.N. (2007) Undulatory Solid Shell Growth of Aluminum Alloy 3003 as a Function of the Wavelength of Grooved Mold Surface Topography. In: Anyalebechi, P.N., Ed., Materials Processing Fundamentals, The Minerals, Metals, and Materials Society, Pittsburgh, 31-47.
Anyalebechi, P.N. (2007) Ungrooved Mold Surface Topography Effects on Subsurface Microstructure. In: Anyalebechi, P.N., Ed., Materials Processing Fundamentals, The Minerals, Metals, and Materials Society, Pittsburgh, 49-62.
Anyalebechi, P.N. (2008) Effect of Cross-Hatched Mold Surface Topography on Shell Morphology in the Solidification of an Aluminum Alloy. In: EPD Congress 2008, The Minerals, Metals, and Materials Society, Pittsburgh, 183-200.
Anyalebechi, P.N. (2012) Effects of Mold Material and Casting Speed on Shell Morphology and Attendant Surface Microstructure of Aluminum Alloy 3003. International Foundry Research, 64, 20-32.
Dong, S., Niiyama, E. and Anzai, K. (1994) Direct Observation of Deformation of Shell Solidified at Melt-Chill Contact. Materials Trans, 35, 196-198. https://doi.org/10.2320/matertrans1989.35.196
Dong, S., et al. (1993) Free Deformation of the Initial Solid Layer of Some Non-Ferrous Alloys. Cast Metals, 6, 115-120. https://doi.org/10.1080/09534962.1993.11819135
Saucedo, I., Beech, J. and Davies, G.J. (1982) Heat Transfer and Solidification Kinetics in Meniscus Zone during Casting. Metals Technology, 9, 282-291. https://doi.org/10.1179/030716982803285693