Following the evolution of currently enforced Performance Based Design standards of reinforced concrete (RC) structures for durability, the designer, rather than complying with given prescriptive limits, may instead specify a cementitious mix design that is proven to exhibit a code prescribed resistance level (class) to a given exposure environment. Such compliance will lead to the protection of the steel reinforcement from corrosion and the cementitious mortar from degradation, during the design lifespan of the structure, under aggressive environmental exposure conditions such as, marine or deicing salts and carbonation. In this context, the enhancement of the physical and durability properties of common cement-based mortars under chloride exposure are experimentally investigated herein. In particular, the experimental program reported herein aims to evaluate the influence of incorporating multi-walled carbon nanotubes on the physical and mechanical properties of reinforced mortars against chloride ions. Furthermore, the anticorrosion protection of cementitious composites prepared with nanomaterials at 0.2% w/w is further investigated, by comparing all test results against reference specimens prepared without any additive. Electrochemical (Half-cell potential, corrosion current) and mass loss of reinforcement steel measurements were performed, while the porosity, capillary absorption and flexural strength were measured to evaluate the mechanical and durability characteristics of the mortars, following a period of exposure of eleven months; SEM images coupled with EDX analysis were further recorded and used for microstructure observation. The test results indicate that the inclusion of the nanomaterials in the mix improved the durability of the mortar specimens, while the nano-modified composites exhibited higher chloride penetration resistance and flexural strength than the corresponding values of the reference mortars. The test results and the comparison between nanomodified and reference mortars showed that the use of CNTs as addition led to protection of steel reinforcing bars against pitting corrosion and a significant improvement in flexural strength and porosity of the mortars.
Ozkan, T., Naraghi, M. and Chasiotis, I. (2010) Mechanical Properties of Vapor Grown Carbon Nanofibers. Carbon, 48, 239-244. https://doi.org/10.1016/j.carbon.2009.09.011
EN 1992-1-1 (2004) Eurocode 2: Design of Concrete Structures—Part 1-1: General Rules and Rules for Buildings. European Committee for Standardization, Brussel.
EN 206 (2004) Eurocode 2: Design of Concrete Structures—Part 1-1: General Rules and Rules for Buildings. European Committee for Standardization, Brussels.
Bethune, D., Kiang, C., de Vries, M. et al. (1993) Cobalt-Catalysed Growth of Carbon Nanotubes with Single-Atomic-Layer Walls. Nature, 363, 605-607. https://doi.org/10.1038/363605a0
Iijima, S. and Ichihashi, T. (1993) Single-Shell Carbon Nanotubes of 1-nm Diameter. Nature, 363, 603-605. https://doi.org/10.1038/363603a0
Iijima, S. (1991) Helical Microtubules of Graphitic Carbon. Nature, 354, 56-58. https://doi.org/10.1038/354056a0
Oberlin, A., Endo, M. and Koyama, T. (1976) Filamentous growth of carbon through benzene decomposition. Journal of Crystal Growth, 32, 335-349. https://doi.org/10.1016/0022-0248(76)90115-9
Grunlan, J., Mehrabi, A., Bannon, M. and Bahr, J. (2004) Water-Based Single-Walled-Nanotube-Filled Polymer Composite with an Exceptionally Low Percolation Threshold. Advanced Materials, 16, 150-153. https://doi.org/10.1002/adma.200305409
Salvetat, J.P., Bonard, J.M., Thomson, N., et al. (1999) Mechanical Properties of Carbon Nanotubes. Applied Physics A, 69, 255-260. https://doi.org/10.1007/s003390050999
Liew, K.M., Kai, M.F. and Zhang, L.W. (2016) Carbon Nanotube Reinforced Cementitious Composites: An Overview. Composites Part A: Applied Science and Manufacturing, 91, 301-323. https://doi.org/10.1016/j.compositesa.2016.10.020
Siddique, R. and Mehta, A. (2014) Effect of Carbon Nanotubes on Properties of Cement Mortars. Construction and Building Materials, 50, 116-129. https://doi.org/10.1016/j.conbuildmat.2013.09.019
Fenner, J.S. and Daniel, I.M. (2014) Hybrid Nanoreinforced Carbon/Epoxy Composites for Enhanced Damage Tolerance and Fatigue Life. Composites Part A: Applied Science and Manufacturing, 65, 47-56. https://doi.org/10.1016/j.compositesa.2014.05.023
Han, B., et al. (2015) Review of Nanocarbon-Engineered Multifunctional Cementitious Composites. Composites Part A: Applied Science and Manufacturing, 70, 69-81. https://doi.org/10.1016/j.compositesa.2014.12.002
Capillary Absorption
Electrochemical Properties
Carbon Nanotubes
Gdoutos, E.E., Konsta-Gdoutos, M.S. and Danoglidis, P.A. (2016) Portland Cement Mortar Nanocomposites at Low Carbon Nanotube and Carbon Nanofiber Content: A Fracture Mechanics Experimental Study. Cement and Concrete Composites, 70, 110-118. https://doi.org/10.1016/j.cemconcomp.2016.03.010
Rovnaník, P., et al. (2016) Carbon Nanotube Reinforced Alkali-Activated Slag Mortars. Construction and Building Materials, 119, 223-229. https://doi.org/10.1016/j.conbuildmat.2016.05.051
Chaipanich, A., et al. (2010) Compressive Strength and Microstructure of Carbon Nanotubes—Fly Ash Cement Composites. Materials Science and Engineering: A, 527, 1063-1067. https://doi.org/10.1016/j.msea.2009.09.039
Del Carmen Camacho, M., et al. (2014) Mechanical Properties and Durability of CNT Cement Composites. Materials, 7, 1640-1651. https://doi.org/10.3390/ma7031640
Konsta-Gdoutos, M.S., et al. (2017) Effect of CNT and CNF Loading and Count on the Corrosion Resistance, Conductivity and Mechanical Properties of Nanomodified OPC Mortars. Construction and Building Materials, 147, 48-57. https://doi.org/10.1016/j.conbuildmat.2017.04.112
Hassan, A., Elkady, H. and Shaaban, I.G. (2019) Effect of Adding Carbon Nanotubes on Corrosion Rates and Steel-Concrete Bond. Scientific Reports, 9, Article No. 6285. https://doi.org/10.1038/s41598-019-42761-2
EN 12390-8 (2009) Testing Hardened Concrete. Depth of Penetration of Water under Pressure. British Standard Institution, London.
Hall, C. and Tse, T.K.M. (1986) Water Movement in Porous Building Materials— VII. The Sorptivity of Mortars. Building and Environment, 21, 113-118. https://doi.org/10.1016/0360-1323(86)90017-X
Gummerson, R.J., Hall, C. and Hoff, W.D. (1980) Water Movement in Porous Building Materials II. Hydraulic Suction and Sorptivity of Brick and Other Masonry Materials. Building and Environment, 15, 101-108. https://doi.org/10.1016/0360-1323(80)90015-3
ASTM C876-87 (2002) Standard Test Method for Half-Cell Potentials of Reinforcing Steel in Concrete. ASTM International.
Chousidis, N., Rakanta, E., Ioannou, I. and Batis, G. (2015) Mechanical Properties and Durability Performance of Reinforced Concrete Containing Fly Ash. Construction and Building Materials, 101, 810-817. https://doi.org/10.1016/j.conbuildmat.2015.10.127
Zafeiropoulou, T., Rakanta, E. and Batis, G. (2013) Carbonation Resistance and Anticorrosive Properties of Organic Coatings for Concrete Structures. Journal of Surface Engineered Materials and Advanced Technology, 3, 67-74. https://doi.org/10.4236/jsemat.2013.31A010
Rashad, A.M. (2017) Effect of Carbon Nanotubes (CNTs) on the Properties of Traditional Cementitious Materials. Construction and Building Materials, 153, 81-101. https://doi.org/10.1016/j.conbuildmat.2017.07.089
Shi, T., et al. (2019) Research Progress on CNTs/CNFs-Modified Cement-Based Composites—A Review. Construction and Building Materials, 202, 290-307. https://doi.org/10.1016/j.conbuildmat.2019.01.024
Gao, Y., et al. (2021) Roles of Carbon Nanotubes in Reinforcing the Interfacial Transition Zone and Impermeability of Concrete under Different Water-to-Cement Ratios. Construction and Building Materials, 272, Article ID: 121664. https://doi.org/10.1016/j.conbuildmat.2020.121664
Abu Taqa, A.G., et al. (2015) The Effect of Interfacial Transition Zone Properties on the Elastic Properties of Cementitious Nanocomposite Materials. Journal of Nanomaterials, 2015, Article ID: 258384. https://doi.org/10.1155/2015/258384
Hu, Y., et al. (2014) Fracture Toughness Enhancement of Cement Paste with Multi-Walled Carbon Nanotubes. Construction and Building Materials, 70, 332-338. https://doi.org/10.1016/j.conbuildmat.2014.07.077
Kang, S.T., Seo, J.Y. and Park, S.H. (2015) The Characteristics of CNT/Cement Composites with Acid-Treated MWCNTs. Advances in Materials Science and Engineering, 2015, Article ID: 308725. https://doi.org/10.1155/2015/308725
Han, B., Zhang, K., Yu X., et al. (2013) Transport Properties of Carbon-Nanotube/Cement Composites. Journal of Materials Engineering and Performance, 22, 184-189. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000435
Han, B., Zhang, K., Yu X. and Kwon, E. (2012) Fabrication of Piezoresistive CNT/ CNF Cementitious Composites with Superplasticizer as Dispersant. Journal of Materials in Civil Engineering, 24, 658-665. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000435
Kim, H.K., Park, I.S. and Lee, H.K. (2014) Improved Piezoresistive Sensitivity and Stability of CNT/Cement Mortar Composites with Low Water-Binder Ratio. Composite Structures, 116, 713-719. https://doi.org/10.1016/j.compstruct.2014.06.007
Li, G.Y., Wang, P.M. and Zhao, X. (2005) Mechanical Behavior and Microstructure of Cement Composites Incorporating Surface-Treated Multi-Walled Carbon Nanotubes. Carbon, 43, 1239-1245. https://doi.org/10.1016/j.carbon.2004.12.017
Konsta-Gdoutos, M.S., Metaxa, Z.S. and Shah, S.P. (2010) Highly Dispersed Carbon Nanotube Reinforced Cement Based Materials. Cement and Concrete Research, 40, 1052-1059. https://doi.org/10.1016/j.cemconres.2010.02.015
Wang, B., Han, Y. and Liu, S. (2013) Effect of Highly Dispersed Carbon Nanotubes on the Flexural Toughness of Cement-Based Composites. Construction and Building Materials, 46, 8-12. https://doi.org/10.1016/j.conbuildmat.2013.04.014
Wille, K. and Loh, K.J. (2010) Nanoengineering Ultra-High-Performance Concrete with Multiwalled Carbon Nanotubes. Transportation Research Record, 2142, 119-126. https://doi.org/10.3141/2142-18
Esmaeili, J. and Mohammadjafari, A.R. (2014) Increasing Flexural Strength and Toughness of Cement Mortar Using Multi-Walled Carbon Nanotubes. International Journal of Nano Dimension, 5, 399-407. https://doi.org/10.7508/ijnd.2014.04.012
Li, W.W., et al. (2015) Investigation on the Mechanical Properties of a Cement-Based Material Containing Carbon Nanotube under Drying and Freeze-Thaw Conditions. Materials, 8, 8780-8792. https://doi.org/10.3390/ma8125491
Chousidis, N., Zacharopoulou, A.K. and Batis, G. (2020) Corrosion Protection of Reinforcement Steel Using Solid Waste Materials in Concrete Production. Magazine of Concrete Research, 72, 271-277. https://doi.org/10.1680/jmacr.17.00537
Makar, J., Margeson, J. and Luh, J. (2005) Carbon Nanotube/Cement Composites—Early Results and Potential Applications. Proceedings of the 3rd International Conference on Construction Materials: Performance, Innovations and Structural Implications, Vancouver, 22-24 August 2005, 1-10.
Makar, J.M. and Chan, G.W. (2009) Growth of Cement Hydration Products on Single-Walled Carbon Nanotubes. Journal of the American Ceramic Society, 92, 1303-1310. https://doi.org/10.1111/j.1551-2916.2009.03055.x
Qiao, G., et al. (2017) Corrosion Behavior of a Steel Bar Embedded in a Cement-Based Conductive Composite. Construction and Building Materials, 134, 388-396. https://doi.org/10.1016/j.conbuildmat.2016.12.087
Voulgari, E., Zacharopoulou, A., Chousidis, N. and Batis, G. (2019) Corrosion Behavior of Reinforcement Steel Embedded in Cement Mortars Using Different Protection Systems. Materials Sciences and Applications, 10, 461-474. https://doi.org/10.4236/msa.2019.106034
Voulgari, E., Zacharopoulou, A., Chousidis, N. and Batis, G. (2019) Effect of Organic Coating Corrosion Inhibitor on Protection of Reinforced Mortar. Journal of Materials Science and Chemical Engineering, 7, 20-34. https://doi.org/10.4236/msce.2019.71003
Chousidis, N., Rakanta, E., Ioannou, I. and Batis, G. (2015) Anticorrosive Effect of Electrochemical Manganese Dioxide By-Products in Reinforced Concrete. Journal of Materials Science and Chemical Engineering, 3, 9-20. https://doi.org/10.4236/msce.2015.35002
Česen, A., Kosec, T. and Legat, A. (2013) Characterization of Steel Corrosion in Mortar by Various Electrochemical and Physical Techniques. Corrosion Science, 75, 47-57. https://doi.org/10.1016/j.corsci.2013.05.015
Wang, T., et al. (2020) Experimental Study on the Effect of Carbon Nanofiber Content on the Durability of Concrete. Construction and Building Material, 250, Article ID: 118891. https://doi.org/10.1016/j.conbuildmat.2020.118891
Torabi, F. and Ahmadi, P. (2020) Chapter 2—Fundamentals of Batteries. In: Torabi, F. and Ahmadi, P., Eds., Simulation of Battery Systems, Academic Press, Cambridge, 55-81.
Sundén, B. (2019) Chapter 2—Electrochemistry and Thermodynamics. In: Sundén, B., Ed., Hydrogen, Batteries and Fuel Cells, Academic Press, Cambridge, 15-36. https://doi.org/10.1016/B978-0-12-816950-6.00002-6