In this study, the characteristics of Graphite/Epoxy Composites (GECs) are evaluated from mechanical perspectives. Different weight percentages of graphite were used (0 - 7 wt%) for tensile and hardness experiments. Then the findings were discussed to ascertain the optimum mixing ratio of the graphite with the epoxy. The primary finding of this study is that the graphite weight fraction has a substantial impact on the composites ’ mechanical performance. At a low percentage (1 wt%), the graphite has little influence on the tensile behaviour. An intermediate weight percentage of the graphite is considered optimum for mechanical performance in the epoxy composites as it slightly reduces the tensile properties and significantly improves the hardness. Micrographs of the fractured surface of specimens showed many signs that clearly explained why fractures had occurred. For instance, when graphite/epoxy composite contained a low proportion of graphite, the cleavage failure was very easy to observe because there was no sign of aggregation or the detachment of fillers.
Yousif, B. and El-Tayeb, N. (2007) On the Effect of Woven Glass Fabric Orientations on Wear and Friction Properties of Polyester Composite. Surface Review and Letters, 14, 489-497. https://doi.org/10.1142/S0218625X07009487
Begum, K. and Islam, M.A. (2013) Natural Fiber as Subtitute to Synthetic Fiber in Polyemrs Composites. Shahjalal University and Technology, Bangladesh.
Mallick, P.K. (1993) Fiber-Reinforced Composites: Materials, Manufacturing, and Design. 2nd Edition, Rev. and Expanded Edition, Mechanical Engineering, M Dekker, New York, 566 p.
Yousif, B. and Chin, C. (2012) Epoxy Composite Based on Kenaf Fibers for Tribological Applications under Wet Contact Conditions. Surface Review and Letters, 19, Article ID: 1250050. https://doi.org/10.1142/S0218625X12500503
Shalwan, A. and Yousif, B. (2013) In State of Art: Mechanical and Tribological Behaviour of Polymeric Composites Based on Natural Fibres. Materials & Design, 48, 14-24. https://doi.org/10.1016/j.matdes.2012.07.014
Williams, J. (2005) The Influence of Repeated Loading, Residual Stresses and Shakedown on the Behaviour of Tribological Contacts. Tribology International, 38, 786-797. https://doi.org/10.1016/j.triboint.2005.02.006
Sun, W.-C., Zhang, P., Zhao, K., Tian, M.-M. and Wang, Y. (2015) Effect of Graphite Concentration on the Friction and Wear of Ni-Al2O3/Graphite Composite Coatings by a Combination of Electrophoresis and Electrodeposition. Wear, 342-343, 172-180. https://doi.org/10.1016/j.wear.2015.08.020
Alizadeh, T. and Hamedsoltani, L. (2014) Graphene/Graphite/Molecularly Imprinted Polymer Nanocomposite as the Highly Selective Gas Sensor for Nitrobenzene Vapor Recognition. Journal of Environmental Chemical Engineering, 2, 1514-1526. https://doi.org/10.1016/j.jece.2014.07.007
Etmimi, H.M., Mallon, P.E. and Sanderson, R.D. (2013) Polymer/Graphite Nanocomposites: Effect of Reducing the Functional Groups of Graphite Oxide on Water Barrier Properties. European Polymer Journal, 49, 3460-3470. https://doi.org/10.1016/j.eurpolymj.2013.08.004
Yu, G.-C., Wu, L.-Z. and Feng, L.-J. (2015) Enhancing the Thermal Conductivity of Carbon Fiber Reinforced Polymer Composite Laminates by Coating Highly Oriented Graphite Films. Materials & Design, 88, 1063-1070. https://doi.org/10.1016/j.matdes.2015.09.096
Hou, Y., Hu, P., Zhang, X. and Gui, K. (2013) Effects of Graphite Flake Diameter on Mechanical Properties and thermal shock behavior of ZrB2-nanoSiC-Graphite Ceramics. International Journal of Refractory Metals and Hard Materials, 41, 133-137. https://doi.org/10.1016/j.ijrmhm.2013.02.015
American Society for Testing and Materials (2000) D638-99. Standard Test Method for Tensile Properties of Plastics. American Society for Testing Materials, Philadelphia.
American Society for Testing Materials (2005) Standard Test Method for Rubber Property—Durometer Hardness. ASTM International, West Conshohocken.
Berto, F., Lazzarin, P. and Ayatollahi, M.R. (2013) Brittle Fracture of Sharp and Blunt V-Notches in Isostatic Graphite under Pure Compression Loading. Carbon, 63, 101-116. https://doi.org/10.1016/j.carbon.2013.06.045
Sengupta, R., Bhattacharya, M., Bandyopadhyay, S. and Bhowmick, A.K. (2011) A Review on the Mechanical and Electrical Properties of Graphite and Modified Graphite Reinforced Polymer Composites. Progress in Polymer Science, 36, 638-670. https://doi.org/10.1016/j.progpolymsci.2010.11.003
Narimissa, E., Gupta, R., Bhaskaran, M. and Sriram, S. (2012) Influence of Nano-Graphite Platelet Concentration on onset of Crystalline Degradation in Polylactide Composites. Polymer Degradation and Stability, 97, 829-832. https://doi.org/10.1016/j.polymdegradstab.2012.02.010
Zheng, W., Lu, X. and Wong, S.C. (2004) Electrical and Mechanical Properties of Expanded Graphite-Reinforced High-Density Polyethylene. Journal of Applied Polymer Science, 91, 2781-2788. https://doi.org/10.1002/app.13460
Ramanathan, T., Abdala, A., Stankovich, S., Dikin, D.A., Herrera-Alonso, M., Piner, R.D., et al. (2008) Functionalized Graphene Sheets for Polymer Nanocomposites. Nature Nanotechnology, 3, 327-331. https://doi.org/10.1038/nnano.2008.96
George, J.J. and Bhowmick, A.K. (2008) Ethylene Vinyl Acetate/Expanded Graphite Nanocomposites by Solution Intercalation: Preparation, Characterization and Properties. Journal of Materials Science, 43, 702-708. https://doi.org/10.1007/s10853-007-2193-6
Celik, C. and Warner, S.B. (2007) Analysis of the Structure and Properties of Expanded Graphite-Filled Poly(Phenylene Ether)/Atactic Polystyrene Nanocomposite Fibers. Journal of Applied Polymer Science, 103, 645-652. https://doi.org/10.1002/app.23772
Suherman, H., Mahyoedin, Y., Septe, E. and Rizade, R. (2019) Properties of Graphite/Epoxy Composites: The In-Plane Conductivity, Tensile Strength and Shore Hardness. AIMS Materials Science, 6, 165-173. https://doi.org/10.3934/matersci.2019.2.165
Kanchanomai, C. and Thammaruechuc, A. (2009) Effects of Stress Ratio on Fatigue Crack Growth of Thermoset Epoxy Resin. Polymer Degradation and Stability, 94, 1772-1778. https://doi.org/10.1016/j.polymdegradstab.2009.06.012
Jawahar, P., Gnanamoorthy, R. and Balasubramanian, M. (2006) Tribological Behaviour of Clay—Thermoset Polyester Nanocomposites. Wear, 261, 835-840. https://doi.org/10.1016/j.wear.2006.01.010
Alamri, H. and Low, I.M. (2012) Effect of Water Absorption on the Mechanical Properties of Nano-Filler Reinforced Epoxy Nanocomposites. Materials & Design, 42, 214-222. https://doi.org/10.1016/j.matdes.2012.05.060
Shivakumar, H., Renukappa, N., Shivakumar, K. and Suresha, B. (2020) The Reinforcing Effect of Graphene on the Mechanical Properties of Carbon-Epoxy Composites. Open Journal of Composite Materials, 10, 27-44. https://doi.org/10.4236/ojcm.2020.102003
Tang, L.-C., Wan, Y.-J., Yan, D., Pei, Y.-B., Zhao, L., Li, Y.-B., et al. (2013) The Effect of Graphene Dispersion on the Mechanical Properties of Graphene/Epoxy Composites. Carbon, 60, 16-27. https://doi.org/10.1016/j.carbon.2013.03.050
Kim, H.S. and Khamis, M.A. (2001) Fracture and Impact Behaviours of Hollow Micro-Sphere/Epoxy Resin Composites. Composites Part A: Applied Science and Manufacturing, 32, 1311-1317. https://doi.org/10.1016/S1359-835X(01)00098-7
Delucchi, M., Ricotti, R. and Cerisola, G. (2011) Influence of Micro- and Nano-Fillers on Chemico-Physical Properties of Epoxy-Based Materials. Progress in Organic Coatings, 72, 58-64. https://doi.org/10.1016/j.porgcoat.2011.02.018
Gultekin, D., Uysal, M., Aslan, S., Alaf, M., Guler, M.O. and Akbulut, H. (2010) The Effects of Applied Load on the Coefficient of Friction in Cu-MMC Brake Pad/Al-SiCp MMC Brake Disc System. Wear, 270, 73-82. https://doi.org/10.1016/j.wear.2010.09.001
Tang, L., Xiong, J., Wan, W., Guo, Z., Zhou, W., Huang, S., et al. (2015) The Effect of Fluid Viscosity on the Erosion Wear Behavior of Ti(C,N)-Based Cermets. Ceramics International, 41, 3420-3426. https://doi.org/10.1016/j.ceramint.2014.10.141