Morphology and solid particle erosion wear behavior of red mud composite coatings
- 1 Metallurgical and Material Engineering Department, National Institute of Technology, Rourkela, India;
- 2 Metallurgical and Material Engineering Department, National Institute of Technology, Rourkela, India;
- 3 Metallurgical and Material Engineering Department, National Institute of Technology, Rourkela, India;
- 4 Mechanical Engineering Department, National Institute of Technology, Rourkela, India
- 5 Chemical Engineering Department, National Institute of Technology, Rourkela, India
Abstract
In order to understand the tribological behavior of red mud composite coatings, the red mud and composite materials like fly ash, carbon and aluminum are being plasma sprayed. The coatings are investigated to know their morphological behavior and erosion wear characteristics. Plasma spraying is done at different plasma arc current like 200, 250, 300 and 400 amperes. Torch input powers maintained as 6, 9, 12 and 16 KW. The substrates chose are rectangular in shape having a dimension of 50 mm × 25 mm × 2 mm. commercially available aluminum, copper, mild steel and stainless steel being used as substrate. Room temperature solid particle erosion trials are carried out using a compressed air blasting type rig under impact angles of 30 o , 60 o and 90 o . The present investigation uses an erosion apparatus of Sand Blast type. The test is conducted as per ASTMG-76 standards. It is analyzed that initially the cumulative coating mass loss increases rapidly and later on becomes almost stagnant. A transient regime in the erosion process exists, during which the incremental erosion rate decreases monotonically down to a steady state erosion rate.
- Gieger, G. (1992) Ceramics coatings enhance material performance. American Ceramic Society Bullet, 71, 1470- 1481.
- Mendelson, M.I. (1978) Theoritical evaluation of wear in plasma-sprayed TiO2 against grey iron. Wear, 50, 71-83. HUdoi:10.1016/0043-1648(78)90246-6U
- Fernandez, J.E., Wang, Y., Tucho, R., Martin-Luengo, M.A., Gancedo, R. and Ricon, A. (1996) Friction and wear behavior of plasma sprayed Cr2O3 coatings against steel in a wide range of sliding velocities and normal loads. Tribology International, 29, 333-343. HUdoi:10.1016/0301-679X(96)00061-8U
- Wei, J. and Xue, Q. (1996) The friction and wear properties of Cr2O3 coating with aqueous lubrication. Wear, 199, 157-159. HUdoi:10.1016/0043-1648(95)06846-5U
- Mohanty, M., Smith, R.W., DeMonte, M., Celis, J.P. and Lugscheider, E. (1996) Sliding wear behavior of thermally sprayed 75/25 Cr2C3/NiCr wear resistant coatings. Wear, 198, 251-266. HUdoi:10.1016/0043-1648(96)06983-9U
- Asanabe, S. (1987) Applications of ceramics for tribological components. Tribology International, 20, 355-364. HUdoi:10.1016/0301-679X(87)90064-8U
- Heiman, R.B. (1996) Plasma-spray coating: Principle and application. Wiley-VCH, Weinheim.
- Budinski, K.G. (1988) Surface engineering for wear resistance. Prentice Hall, New Jersey.
- Stratford, K.N. (1984) Coatings and Surface treatments for corrosion and wear resistance. Corrosion Engineering, Science and Technology, Birmingham.
- Li, J.F., Ding, C.X., Huang, J.Q. and Zahang, P.Y. (1997) Wear mechanism of plasma sprayed Cr3C2-NiCr against TiO2 coating. Wear, 211, 177-184. HUdoi:10.1016/S0043-1648(97)00109-9U
- Angle, P.A. (1976) Impact wear of materials. Elsevier, New York.
- Tilly, G.P. (1979) Erosion caused by impact of solid particles. In: Scott, D., Ed., Treatise on Materials Science and Technology, Vol. 13: Wear. Academic Press, New York, 287-320.
- Field, J.E., Gorham, D.A., Hagan, J.T., Matthewson, M.J., Swain, M.V. and van der Zwaag, S. (1979) 5th international conference on erosion by liquid and solid impact. Cavendish Laboratory, University of Cambridge, Cambridge.
- Field, J.E., Gorham, D.A., Hagan, J.T., Matthewson, M.J., Swain, M.V. and van der Zwaag, S. (1987) 7th international conference on erosion by liquid and solid impact. Cavendish Laboratory, University of Cambridge, Cambridge.