Flexure-Compression Testing of Bridge Timber Piles Retrofitted with Fiber Reinforced Polymers
- 1 Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, Urbana, U.S.A.
- 2 Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, Urbana, U.S.A.
- 3 Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, Urbana, U.S.A.
Abstract
The adequacy of using Fiber Reinforced Polymer (FRP) retrofit technique to restore the flexure-compression behavior of deteriorated bridge timber piles is examined experimentally in this paper. Sixteen specimens are tested monotonically under eccentric compressive loading. The specimens are first tested in their unretrofitted condition to determine their elastic properties. Each specimen is then cut and connected (posted) using the proposed FRP retrofit technique, and retested. The results show that the retrofitted specimens are capable of reaching same or higher strengths than that of the unretrofitted specimens with minimal reduction in their stiffness. Based on the experimental results, a design equation is presented to compute the volumetric ratio of FRP needed for retrofitting bridge timber piles under eccentric load.
- IDOT, “Maximum Legal Dimensions & Weights on State, Federal & Local Routes,” Illinois Department of Transportation, Springfield, IL, 2010.
- IDOT-SIMS, “IDOT Structures Information Management System,” Accessed February 2012. Available from: http:/www.dot.state.il.us/sims/sims.html
- W. Walzer, “The Problem with Rural Bridges,” Cooperative Extension Service, University of Illinois at Urbana- Champaign, IL, 1977.
- W. McCutcheon, R. Gutkowski and R. Moody, “Performance and Rehabilitation of Timber Bridges,” Transportation Research Record 1053, 1986, pp. 65-79.
- T.J. Wipf, F. S. Fanous, F. W. Klaiber and A. S. Eapen, “Evaluation of Appropriate Maintenance, Repair and Rehabilitation Methods for Iowa Bridges,” Final Report, Iowa DOT Project TR-429, 2003.
- D. J. Borello, B. Andrawes, J. F. Hajjar, S. M. Olson and J. Hansen, “Experimental and Analytical Investigation of Bridge Timber Piles under Eccentric Loads,” Engineering Structures, Vol. 32, No. 8, 2010, pp. 2237-2246. doi:10.1016/j.engstruct.2010.03.026
- D. J. Borello, B. Andrawes, J. F. Hajjar, S. M. Olson, J. Hansen and J. Buenjer, “Forensic Collapse Investigation of a Concrete Bridge with Timber Piers,” Research Report FHWA-ICT-09-042, Illinois Center for Transportation, Springfield, IL, 2009.
- M. Hagos, “Repair of Heavily Decayed Timber Piles Using Glass Fiber Reinforced Polymers (GFRP) and Cementitious Grout,” M.Sc. Thesis, University of Manitoba, Winipeg, Manitoba, Canada, 2001.
- A. M. Pozolo, “Transfer and Development Lengths of Steel Strands in Full-Scale Prestressed Self-Consolidating Concrete Bridge Girders,” M.S. Thesis, University of Illinois at Urbana-Champaign, Urbana, Urbana, 2010.
- J. Ambrose and P. Tripeny, “Simplified Design of Wood Structures,” Sixth Edition, John Wiley & Sons, Inc., 2009.
- A. H. Buchanan, “Combined Bending and Axial Loading in Lumber”, Journal of Structural Engineering, Vol. 112, No. 12, 1986, pp. 2592-2609. doi:10.1061/(ASCE)0733-9445(1986)112:12(2592)
- F.C. Campbell, “Structural Composite Materials,” ASM International, Materials Park, Ohio, 2010.
- American Forest & Paper Association (AFPA), “National Design Specification (NDS) for Wood Construction,” Washington DC, 2005.