A Computer Program for Dynamic Load Simulation of Spur Gears with Asymmetric and Symmetric Teeth
- 1 Department of Mechanical Engineering, Uludag University, Bursa, Turkey
- 2 Department of Mechanical Engineering, Texas Tech University, Lubbock, USA
- 3 Department of Electronics Engineering, Uludag University, Bursa, Turkey
Abstract
An important concern in gear design is to reduce the dynamic load and noise of gear systems. It has been found that the noise generated from gearing is basically due to gearbox vibration excited by the dynamic load. Since one of the situations that demand high performance is the high rotational speeds, there is a need to understand the dynamic behavior of the gears at such speeds. Such knowledge would shed light on detrimental characteristics like dynamic loads and vibrations. An efficient way in performing studies on the dynamic behavior of gears is using computer aided analysis on numerical models. In this paper, a developed computer program is introduced to analyze dynamic behavior of spur gears with asymmetric teeth that have a potential use for higher performance in wind turbine gearboxes. This program can be used to compare conventional spur gears with symmetric teeth and spur gears with asymmetric teeth. By using this program, gear designers can design a gear pair and obtain results, e.g dynamic Load, transmitted torque, static transmission error, and frequency spectra of static transmission error etc., just by pressing a command button.
- F. L. Litvin, D. Vecchiato, K. Yukishima, A. Fuentes, I. Gonzalez-Perez and K. Hayasaka, “Reduction of Noise of Loaded and Unloaded Misaligned Gear Drives,” Computer Methods in Applied Mechanics and Engineering, Vol. 195, No. 41-43, 2006, pp. 5523-5536. doi:10.1016/j.cma.2005.05.055
- M. ?kerblom, “Gear Noise and Vibration—A Literature Survey,” Stockholm, 2001, p. 26.
- H. N. Ozguven and D. R. Houser, “The Mathematical Models Used in Gear Dynamics—A Review,” Journal of Sound and Vibration, Vol. 121, No. 3, 1988, pp. 383-411. doi:10.1016/S0022-460X(88)80365-1
- A. Parey and N. Tandon, “Spur Gear Dynamic Models Including Defects: A Review,” Shock Vibration Digest, Vol. 35, No. 6, 2003, pp. 465-78. doi:10.1177/05831024030356002
- Y. Tearuchi and M. Hidetaro, “Comparison of Theories and Experimental Results for Surface Temperature of Spur Gear Teeth,” Journal of Engineering for Industry, Transactions of the ASME, Vol. 96, No. 11, 1974, pp. 41-50.
- K. Ichimaru and F. Hirano, “Dynamic Behavior of Heavy-Loaded Spur Gears,” Journal of Engineering for Industry, Transactions of the ASME, Vol. 96, No. 2, 1974, pp. 373-381.
- K. L. Wang and H. S. Cheng, “Numerical Solution to the Dynamic Load, Film Thickness, and Surface Temperatures in Spur Gears—Part 2 Results,” Journal of Mechanical Design, Vol. 103, No. 4, 1981, pp. 188-194. doi:10.1115/1.3254860
- K. L. Wang, H. S. Cheng, K. L. Wang and H. S. Cheng, “Numerical Solution to the Dynamic Load, Film Thickness, and Surface Temperatures in Spur Gears—Part 1. Analysis,” Journal of Mechanical Design, Vol. 103, No. 4, 1981, pp. 177-187. doi:10.1115/1.3254859
- S. M. A. Arikan, “Dynamic Load and Contact Stress Analysis of Spur Gears,” 17th Design Automation Conference presented at the 1991 ASME Design Technical Conferences, Miami, 1991, pp. 85-91.
- J. H. Kuang and A. D. Lin, “The Effect of Tooth Wear on the Vibration Spectrum of a Spur Gear Pair,” Journal of Vibration and Acoustics-Transactions of the Asme, Vol. 123, No. 3, 2001, pp. 311-317. doi:10.1115/1.1379371
- J. H. Kuang, A. D. Lin, J. H. Kuang and A. D. Lin, “Theoretical Aspects of Torque Responses in Spur Gearing Due to Mesh Stiffness Variation,” Mechanical Systems and Signal Processing, Vol. 17, No. 2, 2003, pp. 255-271. doi:10.1006/mssp.2002.1516
- A. Andersson, “An Analytical Study of the Effect of the Contact Ratio on Spur Gear Dynamic Response,” Journal of Mechanical Design, Vol. 122, No. 4, 2000, pp. 508514. doi:10.1115/1.1320819