In order to clarify the reason why the creep rupture time of pre-strained Ni-23Cr-7W Alloy (HR6W) is longer than that of the non-pre-strained HR6W, microstructures of HR6W after a series of creep tests were investigated. The creep tests were conducted at 750 ° C, 90 and 100 MPa. In the pre-strained samples, the grain boundary shielding ratio by precipitates was larger than that of the non-pre-strained sample. In addition, in the pre-strained samples the size of the M 23 C 6 carbide in the grains was finer than in the non-pre-strained sample. The W content in the M 23 C 6 carbide in the pre-strained samples tended to be larger than in the non-pre-strained sample. Therefore, the Ostwald ripening of the carbide was delayed and the size of M 23 C 6 carbide was thought to be fine for a long time. These observations show that creep strength in the pre-strained samples is higher than that of the non-pre-strained sample because of both precipitation strengthening inside of the grains and grain boundaries.
Kubushiro, K., Nomura, K., Matuoka, T., Nakagawa, H. and Muroki, K. (2016) Development of Boiler Technology for 700°C A-USC Plant. IHI Engineering Review, 49, 34-43.
Takano, S., Aoki, H., Kubushiro, K., Tomiyama, N. and Nakagawa, H. (2009) Development of 700 Degree Celsius Class Advanced Ultra-Supercritical Boiler. IHI Engineering Review, 49, 185-191. (In Japanese)
Fukuda, M., Yoshida, T., Iseda, A., Semba, H., Saito, E., Kitamura, M., Dohi, T., Aoki, H., Muroki, K., Fukutomi, H., Sato, K., Satio, N., Hirakawa, Y., Nishii, T., Takahashi, T. and Matubara, Y. (2016) 700°C A-USC Technology Development in Japan. Proceedings of 8th International Conference on Advances in Materials Technology for Fossil Power Plants, Algarve, 10-14 October 2016, 12-23.
Fukuda, M. (2007) The Next Generation of USC Technology in Japan. Proceedings of International Conference on Power Engineering, Hagzhou, 23-27 October 2007, 20-25. https://doi.org/10.1007/978-3-540-76694-0_3
Kubusiro, K., Nomura, K., Nakagawa, H., Ohkuma, Y. and Muroki, K. (2015) Development of Fabrication Technology for the A-USC Boiler. Proceedings of International Conference on Power Engineering, Yokohama, 30 November-4 December 2015.
Abe, F. (2015) Research and Development of Heat-Resistant Materials for Advanced USC Power Plants with Steam Temperatures of 700°C and above. Engineering, 1, 211-224. https://doi.org/10.15302/J-ENG-2015031
Umaki, H., Kajigaya, I., Kunihiro, T., Totsuka, T., Nakashiro, M. and Kume, T. (1991) Application of Large Diameter Seam Welded Pipes and Header of Super 9Cr Steel for 700 MW Coal-Fired Boiler with 593°C Reheat Steam Temperature. Ishikawajima-Harima Engineering Review, 31, 339-345. (In Japanese)
Semba, H., Okada, H., Hamaguti, T., Ishikawa, S. and Yoshizawa, M. (2013) Development of Boiler Tubes and Pipes for Advanced USC Power Plants. Nippon Steel & Sumitomo Metal Technical Report, 397, 71-77. (In Japanese)
Semba, H., Okada, H., Igarashi, M., Hirata, H. and Yoshizawa, M. (2010) Development of Fe-Ni and Ni-Base Alloys without γ’ Strengthening for Advanced USC Boilers. Proceedings of 9th Liege Conference on Materials for Advanced Power Engineering, Liège, 14-17 September 2014, 360-369.
Furuta, T., Ogawa, Y. and Nagasaki, R. (1973) The Effect of Cold Working on Creep Properties of 316 Stainless Steel USED as a Fuel Cladding in Fast Breeder Reactors. Tetsu-to-Hagane, 59, 949-954. (In Japanese)
Masuyama, F. (2007) Cold Work Effect on Creep Rupture Strength of Austenitic Boiler Steels. Proceedings of 8th International Conference on Creep and Fatigue at Elevated Temperatures, CREEP 2007-26469. https://doi.org/10.1115/CREEP2007-26469
Ogawa, K., Ishii, M., Yoshizawa, H., Oote, S. and Wada, Y. (1986) Pre-Strain Effect on the Elevated Temperature Mechanical Properties of Type 304 Stainless Steel. The Society of Materials Science, 35, 1284-1290. (In Japanese)
Nakzawa, T. and Abo, H. (1977) The Effects of Some Factors on the Creep Behavior of Type 304 Stainless Steel. Tetsu-to-Hagane, 63, 1150-1159. (In Japanese) https://doi.org/10.2355/tetsutohagane1955.63.7_1150
Saito, N. (2007) Creep Deformation Behavior and Microstructural Degradation during Creep of Pre-Strained 25Cr-20Ni-Nb-N Steel. Proceedings of 8th International Conference on Creep and Fatigue at Elevated Temperatures, CREEP 2007-26764. https://doi.org/10.1115/CREEP2007-26764
Okada, H., Semba, H., Ishikawa, S. and Yoshizawa, M. (2012) Effect of Cold Working on Creep Properties of a 23Cr-45Ni-7W Alloy. CAMP-ISIJ, 25, 405. (In Japanese)
Saito, N., Komai, N., Hashimoto, K. and Kitamura, M. (2016) Long-Term Creep Rupture Properties and Microstructures in Hr6w (44Ni-23Cr-7W) for A-USC Boilers. Proceedings of 8th International Conference on Advances in Materials Technology for Fossil Power Plants, 419-429.
Kubushiro, K., Shioda, Y. and Nomura, K. (2017) Effect of Pre-Strain on the Creep Strength of Ni-Based Alloys for A-USC Boilers. Transactions of the Indian Institute of Metals, 70, 1261-1268. https://doi.org/10.1007/s12666-016-0919-3
Nomura, K., Shioda, Y., Kubushiro, K., Nakagawa, H. and Murata, Y. (2017) Strain Analysis of Weld Joint of 23Cr-45Ni-7W Alloy by XRD and EBSD Method. Journal of the Society of Materials Science, 66, 51-57. (In Japanese) https://doi.org/10.2472/jsms.66.51
Umezaki, S., Murata, Y., Nomura, K. and Kubushiro, K. (2014) Quantitative Analysis of Dislocation Density in an Austenitic Steel after Plastic Deformation. Journal of Japan Institute Metals, 78, 218-224. (In Japanese) https://doi.org/10.2320/jinstmet.J2014001
Elbatahgy, A.M., Matsuo, T. and Kikuchi, M. (1990) Grain Boundary Precipitation Strengthening due to γ’ Phase in High Temperature Creep of a Ni-Base Superalloy. Tetsu-to-Hagane, 76, 767-774. (In Japanese) https://doi.org/10.2355/tetsutohagane1955.76.5_767
Kondo, Y., Ishizaki, A. and Namekata, J. (1990) Effect of Carbide Precipitation Formed on Dislocations along Grain Boundaries on High Temperature Creep Resistance of a Ni-30Cr Alloy. Tetsu-to-Hagan, 76, 1187-1194. (In Japanese) https://doi.org/10.2355/tetsutohagane1955.76.7_1187
Tarigan, I., Takata, N. and Takeyama, M. (2012) Grain Boundary Precipitation Strengthening Mechanism by Fe2Nb Laves Phase in Creep of Fe-20Cr-30Ni-2Nb Austenitic Heat Resistant Steel. Proceedings of 12th International Conference on Creep and Fracture of Engineering Materials and Structures (JIMIS 11).
Kurata, K., Takata, N., Matsuo, T. and Takeyama, M. (2008) Effect of Grain Boundary Laves Phase Fe2Nb on Creep Resistance of Fe-20Cr-30Ni-2Nb Austenitic Heat Resistance Steel. Proceedings of Japan Society for Promotion of Science 123rd Committee on Heat Resisting Materials and Alloys, 49, 379-390. (In Japanese)
Tarigan, I., Kurata, K., Takata, N., Matsuo, T. and Takeyama, M. (2011) Novel Concept of Creep Strengthening Mechanism Using Grain-Boundary Fe2Nb Laves Phase in Austenitic Heat Resistant Steel. Materials Research Society Symposia Proceedings, 1295, 317-322. https://doi.org/10.1557/opl.2011.558
Weiss, B. and Stickler, R. (1972) Phase Instabilities during High Temperature Exposure of 316 Austenitic Stainless Steel. Metallurgical Transactions, 3, 852-866. https://doi.org/10.1007/BF02647659
Spruiell, J.E., Scottm, J.A., Ary, C.S. and Hardin, R.L. (1973) Microstructural Stability of Thermal-Mechanically Pretreated Type 316 Austenitic Stainless Steel. Metallurgical Transactions, 4, 1533-1544.
Mino, K., Ohtomo, A. and Saiga, Y. (1977) Effect of Grain Boundary Migration and Recrystallization on the Creep Strength of Inconel 617. Tetsu-to-Hagane, 63, 2372-2380. (In Japanese) https://doi.org/10.2355/tetsutohagane1955.63.14_2372
Trotter, G., Rayner, G., Baker, I. and Munroe, P.R. (2014) Accelerated Precipitation in the AFA Stainless steel Fe-20Cr-30Ni-2Nb-5Al via Cold Working. Intermetallics, 53, 120-128.
Qilong, Y. (1990) Theory of Nucleation on Dislocations. Chin. J. Met. Sci. Technol., 6, 239-243.
Fujii, T., Onaka, S. and Kato, M. (2004) Energy Consideration for Preferential Precipitation on Dislocations. Materia Japan, 43, 925-930. (In Japanese) https://doi.org/10.2320/materia.43.925
Hald, J. (2008) Microstructure and Long-Term Creep Properties of 9-12% Cr Steels. International Journal of Pressure Vessels and Piping, 85, 30-37.
Yoshizawa, M., Igarashi, M. and Nishizawa, T. (2005) Effect of Tungsten on the Ostwald Ripening of M23C6 Carbides in Martensitic Heat Resistant Steel. Tetsu-to-Hagane, 91, 272-277. (In Japanese) https://doi.org/10.2355/tetsutohagane1955.91.2_272