Improvement of Interlaminar Fracture Properties of Out of Autoclave Manufactured Carbon Fiber Reinforced Polymers Using Multi-Walled Carbon Nanotubes — Oak Academic Publishing
Research ArticleOpen AccessGoogle Scholar indexed
Improvement of Interlaminar Fracture Properties of Out of Autoclave Manufactured Carbon Fiber Reinforced Polymers Using Multi-Walled Carbon Nanotubes
Department of Mechanical Engineering and Aeronautics, University of Patras, Patras, Greece
,
Department of Mechanical Engineering and Aeronautics, University of Patras, Patras, Greece
,
Institute of Chemical Engineering Sciences, Foundation for Research and Technology Hellas (ICE-HT/FORTH), Patras, Greece
,
Institute of Chemical Engineering Sciences, Foundation for Research and Technology Hellas (ICE-HT/FORTH), Patras, Greece
1 Department of Mechanical Engineering and Aeronautics, University of Patras, Patras, Greece
2 Department of Mechanical Engineering and Aeronautics, University of Patras, Patras, Greece
3 Institute of Chemical Engineering Sciences, Foundation for Research and Technology Hellas (ICE-HT/FORTH), Patras, Greece
4 Institute of Chemical Engineering Sciences, Foundation for Research and Technology Hellas (ICE-HT/FORTH), Patras, Greece
The present study aims to the development of Out of Autoclave (OoA) Carbon Fiber Reinforced Polymers (CFRPs) with increased interlaminar fracture toughness by using MWCNTs. The introduction of MWCNTs into the structure of CFRPs has been succeeded by using carbon nanotube-enriched sizing agent for the pretreatment of the fiber preform using an in-house developed methodology that can be easily scaled up. The positive effect of the proposed methodology on the interlaminar fracture toughness of the CFRP laminate was assessed by the increase of Mode I and Mode II interlaminar fracture toughness of the composites. Different wt% MWCNTs concentrations were used (namely 0.5%, 1%, 1.5% and 2.5%). It was found that the nanomodified composites exhibit a significant increase of the interlaminar critical strain energy release rate GIC and GIIC of the order of 103% and 62% respectively, in the case of 1.5 wt% MWCNTs weight content. Scanning Electron Microscopy (SEM) of the fracture surfaces of CFRP samples revealed the contribution and the associated synergistic mechanisms of MWCNTs to the increase of the crack propagation resistance in the case of nano-modified CFRPs compared to the reference material.
Mouritz, A.P. (2007) Review of Z-Pinned Composite Laminates. Composites Part A: Applied Science and Manufacturing, 38, 2383-2397. https://doi.org/10.1016/j.compositesa.2007.08.016
Cartié, D.D.R., Troulis, M. and Partridge, I.K. (2006) Delamination of Z-Pinned Carbon Fibre Reinforced Laminates. Composites Science and Technology, 66, 855-861. https://doi.org/10.1016/j.compscitech.2004.12.018
M’membe, B., Gannon, S., Yasaee, M., Hallett, S.R. and Partridge, I.K. (2016) Mode II Delamination Resistance of Composites Reinforced with Inclined Z-Pins. Materials & Design, 94, 565-572. https://doi.org/10.1016/j.matdes.2016.01.051
Dransfield, K., Baillie, C. and Mai, Y.W. (1994) Improving the Delamination Resistance of CFRP by Stitching—A Review. Composites Science and Technology, 50, 305-317. https://doi.org/10.1016/0266-3538(94)90019-1
Göktaş, D., Kennon, W.R. and Potluri, P. (2017) Improvement of Mode I Interlaminar Fracture Toughness of Stitched Glass/Epoxy Composites. Applied Composite Materials, 24, 351-375. https://doi.org/10.1007/s10443-016-9560-x
Fishpool, D.T., Rezai, A., Baker, D., Ogin, S.L. and Smith, P.A. (2013) Interlaminar Toughness Characterisation of 3D Woven Carbon Fibre Composites. Plastics Rubber and Composites, 42, 108-114. https://doi.org/10.1179/1743289812Y.0000000036
Unnikrishnan, K.P. and Thachil, E.T. (2006) Toughening of Epoxy Resins. Designed Monomers & Polymers, 9, 129-152. https://doi.org/10.1163/156855506776382664
Gorbatikh, L., Lomov, S.V. and Verpoest, I. (2011) Nano-Engineered Composites: A Multiscale Approach for Adding Toughness to Fibre Reinforced Composites. Procedia Engineering, 10, 3252-3258. https://doi.org/10.1016/j.proeng.2011.04.537
Borowski, E., Soliman, E., Kandil, U.F. and Taha, M.R. (2015) Interlaminar Fracture Toughness of CFRP Laminates Incorporating Multi-Walled Carbon Nanotubes. Polymers (Basel), 7, 1020-1045. https://doi.org/10.3390/polym7061020
Godara, A., Mezzo, L., Luizi, F., Warrier, A., Lomov, S.V. and van Vuure, A.W. (2009) Influence of Carbon Nanotube Reinforcement on the Processing and the Mechanical Behaviour of Carbon Fiber/Epoxy Composites. Carbon NY, 47, 2914-2923. https://doi.org/10.1016/j.carbon.2009.06.039
Coleman, J.N., Khan, U., Blau, W.J. and Gun’ko, Y.K. (2006) Small But Strong: A Review of the Mechanical Properties of Carbon Nanotube-Polymer Composites. Carbon NY, 44, 1624-1652. https://doi.org/10.1016/j.carbon.2006.02.038
Karapappas, P., Vavouliotis, A., Tsotra, P., Kostopoulos, V. and Paipetis, A. (2009) Enhanced Fracture Properties of Carbon Reinforced Composites by the Addition of Multi-Wall Carbon Nanotubes. Journal of Composite Materials, 43, 977-985. https://doi.org/10.1177/0021998308097735
Thostenson, E.T., Ren, Z. and Chou, T.W. (2001) Advances in the Science and Technology of Carbon Nanotubes and Their Composites: A Review. Composites Science and Technology, 6, 1899-1912. https://doi.org/10.1016/S0266-3538(01)00094-X
Kostopoulos, V., Baltopoulos, A., Karapappas, P., Vavouliotis, A. and Paipetis, A. (2010) Impact and After-Impact Properties of Carbon Fibre Reinforced Composites Enhanced with Multi-Wall Carbon Nanotubes. Composites Science and Technology, 70, 553-563. https://doi.org/10.1016/j.compscitech.2009.11.023
Kostopoulos, V., Karapappas, P., Loutas, T., Vavouliotis, A., Paipetis, A. and Tsotra, P. (2011) Interlaminar Fracture Toughness of Carbon Fibre-Reinforced Polymer Laminates with Nano- and Micro-Fillers. Strain, 47, 269-282. https://doi.org/10.1111/j.1475-1305.2008.00612.x
Gojny, F.H., Wichmann, M.H.G., Köpke, U., Fiedler, B. and Schulte, K. (2004) Carbon Nanotube-Reinforced Epoxy-Composites: Enhanced Stiffness and Fracture Toughness at Low Nanotube Content. Composites Science and Technology, 64, 2363-2371. https://doi.org/10.1016/j.compscitech.2004.04.002
Davis, D.C. and Whelan, B.D. (2011) An Experimental Study of Interlaminar Shear Fracture Toughness of a Nanotube Reinforced Composite. Composites Part B: Engineering, 42, 105-116. https://doi.org/10.1016/j.compositesb.2010.06.001
Zhou, Y., Pervin, F., Lewis, L. and Jeelani, S. (2008) Fabrication and Characterization of Carbon/Epoxy Composites Mixed with Multi-Walled Carbon Nanotubes. Materials Science and Engineering: A, 475, 157-165. https://doi.org/10.1016/j.msea.2007.04.043
Fan, Z., Santare, M.H. and Advani, S.G. (2008) Interlaminar Shear Strength of Glass Fiber Reinforced Epoxy Composites Enhanced with Multi-Walled Carbon Nanotubes. Composites Part A: Applied Science and Manufacturing, 39, 540-554. https://doi.org/10.1016/j.compositesa.2007.11.013
Qiu, J., Zhang, C., Wang, B. and Liang, R. (2007) Carbon Nanotube Integrated Multifunctional Multiscale Composites. Nanotechnology, 18, Article ID: 275708. https://doi.org/10.1088/0957-4484/18/27/275708
Tugrul, S.A., Tanoglu, M. and Schulte, K. (2008) Mode I and Mode II Fracture Toughness of E-Glass Non-Crimp Fabric/Carbon Nanotube (CNT) Modified Polymer Based Composites. Engineering Fracture Mechanics, 75, 5151-5162. https://doi.org/10.1016/j.engfracmech.2008.08.003
Sadeghian, R., Gangireddy, S., Minaie, B. and Hsiao, K.T. (2006) Manufacturing Carbon Nanofibers Toughened Polyester/Glass Fiber Composites Using Vacuum Assisted Resin Transfer Molding for Enhancing the Mode-I Delamination Resistance. Composites Part A: Applied Science and Manufacturing, 37, 1787-1795. https://doi.org/10.1016/j.compositesa.2005.09.010
Kim, K.J., Yu, W.R., Youk, J.H. and Lee, J. (2012) Factors Governing the Growth Mode of Carbon Nanotubes on Carbon-Based Substrates. Physical Chemistry Chemical Physics, 14, 140-141. https://doi.org/10.1039/c2cp42566a
He, X., Zhang, F., Wang, R. and Liu, W. (2007) Preparation of a Carbon Nanotube/Carbon Fiber Multi-Scale Reinforcement by Grafting Multi-Walled Carbon Nanotubes onto the Fibers. Carbon NY, 45, 2559-2563. https://doi.org/10.1016/j.carbon.2007.08.018
Karapappas, P., Tsantzalis, S., et al. (2008) Multi-Wall Carbon Nanotubes Chemically Grafted and Physically Adsorpted on Reinforcing Carbon Fibres. Advanced Composites Letters, 17, 103-107. https://doi.org/10.1177/096369350801700304
An, Q., Rider, A.N. and Thostenson, E.T. (2012) Electrophoretic Deposition of Carbon Nanotubes onto Carbon-Fiber Fabric for Production of Carbon/Epoxy Composites with Improved Mechanical Properties. Carbon NY, 50, 4130-4143. https://doi.org/10.1016/j.carbon.2012.04.061
De Greef, N., Zhang, L., Magrez, A., Forró, L., Locquet, J.P. and Verpoest, I. (2015) Direct Growth of Carbon Nanotubes on Carbon Fibers: Effect of the CVD Parameters on the Degradation of Mechanical Properties of Carbon Fibers. Diamond and Related Materials, 1, 39-48. https://doi.org/10.1016/j.diamond.2014.11.002
Zhang, J., Li, W., Soga, T., Jimbo, T. and Tanji, T. (2012) Synthesis of High-Density Vertically Aligned Carbon Nanotubes Using Ultrasonic Nebulizer. Material Science and Applications, 3, 213-217. https://doi.org/10.4236/msa.2012.34031
Zhang, H., Liu, Y., Kuwata, M., Bilotti, E. and Peijs, T. (2015) Improved Fracture Toughness and Integrated Damage Sensing Capability by Spray Coated CNTs on Carbon Fibre Prepreg. Composites Part A: Applied Science and Manufacturing, 70, 102-110. https://doi.org/10.1016/j.compositesa.2014.11.029
Resoltech Resin Resolcoat 1400 Data Sheet. https://www.resoltech.com/en/products/epoxy/1400-detail.html
Nanocyl Sizing Agent Data Sheet. http://www.nanocyl.com/product
ASTM D 5528-01, ASTM Int. Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites. Standard No. ASTM D5528-01.
ASTM D 7905/D7905M-14, ASTM Int. Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites.