Effects of R134a Saturation Temperature on a Shell and Tube Condenser with the Nanofluid Flow in the Tube Using the Thermal Efficiency and Effectiveness Concepts
- 1 Department of Mechanics and Energy, State University of Rio de Janeiro, DEM/FAT/UERJ, Resende, Brazil
Abstract
The work’s objective is to analyze the influence of the saturation temperature of the R134a refrigerant on the thermal performance of a shell and tube type condenser, with water and aluminum oxide (Al 2 O 3 ) nanoparticles flowing into the tube. For analysis, the heat exchanger is subdivided into three regions: subcooled liquid, saturated steam, and superheated steam. The shell and tube heat exchanger assumed as the basis for the study has 36 tubes, with rows of 4 tubes in line and three passes into the tube in each region. The parameters used to analyze the performance are efficiency and effectiveness, through variations of quantities such as saturation temperature, the nanofluid’s mass flow rate, fraction in the nanoparticles’ volume, and the number of passes in the tube in each region of the heat exchanger. The obtained results demonstrate that the efficiency is relatively high in all the analyzed situations. In each saturation temperature, the effectiveness can be increased by introducing fractions of nanoparticles in the water or increasing the number of passes in the tube.
- Nogueira, E. (2020) Theoretical Analysis of a Shell and Tubes Condenser with R134a Working Refrigerant and Water-Based Oxide of Aluminum Nanofluid (Al2O3). Journal of Materials Science and Chemical Engineering, 8, 1-22. https://doi.org/10.4236/msce.2020.811001
- Nogueira, E. (2020) Thermal Performance in Heat Exchangers by the Irreversibility, Effectiveness, and Efficiency Concepts Using Nanofluids. Journal of Engineering Sciences, 7, 1-7. https://doi.org/10.21272/jes.2020.7(2).f1
- Lee, T.-S. and Mai, J.-W. (2011) Modeling and Simulation of the Heat Transfer Behavior of a Shell-and-Tube Condenser for a Moderately High-Temperature Heat Pump. In: Ahsan, A., Ed., Two-Phase Flow, Phase Change and Numerical Modeling, InTech, London, 61-82. https://doi.org/10.5772/19596
- Bejan, A. (1987) The Thermodynamic Design of Heat and Mass Transfer Processes and Devices. International Journal of Heat and Fluid Flow, 8, 258-276. https://doi.org/10.1016/0142-727X(87)90062-2
- Fakheri, A. (2007) Heat Exchanger Efficiency. Transactions of the ASME, 129, 1268-1276. https://doi.org/10.1115/1.2739620
- Almurtaji, S., Ali, N., Teixeira, J.A. and Addali, A. (2020) On the Role of Nanofluids in Thermal-Hydraulic Performance of Heat Exchangers—A Review. Nanomaterials, 10, 734. https://doi.org/10.3390/nano10040734
- Thakur, G. and Singh, G. (2017) An Experimental Investigation of Heat Transfer Characteristics of Water-Based (Al2O3) Nanofluid Operated Shell and Tube Heat Exchanger with Air Bubble Injection Technique. International Journal of Engineering & Technology, 6, 83-90. https://doi.org/10.14419/ijet.v6i4.7881
- Sun, Y., Wang, X., Long, R., Yuan, F. and Yang, K. (2019) Numerical Investigation and Optimization on Shell Side Performance of a Shell and Tube Heat Exchanger with Inclined Trefoil-Hole Baffles. Energies, 12, 4138. https://doi.org/10.3390/en12214138
- Mostafa, A.A.H., Khalil, E.E., El-Hariry, G., et al. (2017) Shell and Tube Heat Exchanger Performance. AIAA Propulsion and Energy Forum, 15th International Energy Conversion Engineering Conference, Atlanta, GA, 10-12 July 2017.
- Roy, R. and Mandal, B.K. (2014) Computer-Based Thermodynamic Properties of Alternative Refrigerant R-134a. Engineering Sciences International Research Journal, 2, 163-169.
- Vajjha, R.S. and Das, D.K. (2012) A Review and Analysis on Influence of Temperature and Concentration of Nanofluids on Thermophysical Properties, Heat Transfer and Pumping Power. International Journal of Heat and Mass Transfer, 55, 4063-4078. https://doi.org/10.1016/j.ijheatmasstransfer.2012.03.048