The idea of adding reinforcing materials, or fillers, to polymers has been around for many decades. The reason for the creation of polymer composite materials came about due of the need for materials with specific properties for specific applications. For example, composite materials are unique in their ability to allow brittle and ductile materials to become softer and stronger. It is expected that good tribological properties can be obtained for polymers filled with nano-scale fillers. A soft plastic can become harder and stronger by the addition of a light weight high stiffness material. In the present work, the effect of adding different percentages of carbon nano-particulates to polystyrene (PS) on the mechanical properties of nano-composites produced was investigated. Based on the experimental observations, it was found that as the percentage of the carbon nano-particulates (CNP S ) increased hardness increased and consequently friction coefficient remarkably decreased.
C. L. E. Nielsen and R. F. Landel, “Mechanical Properties of Polymers and Composites,” 2nd Edition, Marcel Deckker, New York, 1994.
S. Nikkeshi, M. Kudo and T. Masuko, “Dynamic Viscoelastic Properties and Thermal Properties of Powder-Epoxy Resin Composites,” Journal of Applied Polymer Science, Vol. 69, No. 13, 1998, pp. 2593-2598. doi:10.1002/(SICI)1097-4628(19980926)69:13 3.0.CO;2-5
K. Zhu and S. Schmauder, “Prediction of the Failure Properties of Short Fiber Reinforced Composites with Metal and Polymer Matrix,” Computational Materials Science, Vol. 28, No. 3-4, 2003, pp. 743-748. doi:10.1016/j.commatsci.2003.08.028
I. H. Tavman, “Thermal and Mechanical Properties of Copper Powder Filled Polyethylene Composites,” Powder Technology, Vol. 91, No. 1, 1997, pp. 63-67. doi:10.1016/S0032-5910(96)03247-0
T. Ahmad and O. Mamat, “The Development and Characterization of Zirconia-Silica Sand Nanoparticles Composites,” World Journal of Nano Science and Engineering, Vol. 1, No. 1, 2011, pp. 7-14. doi:10.4236/wjnse.2011.11002
S. T. Peters, “Handbook of Composites,” 2nd Edition, Chapman and Hall, London, 1998.
R. N. Rothon, “Mineral Fillers in Thermoplastics I Raw Materials and Processing,” In: J. Jancar, Ed., Advances in Polymer Science, Vol. 139, Springer, Berlin, 1999, p. 67.
M. Sumita, T. Shizuma, K. Miyasaka and K. Ishikawa, “Effect of Reducible Properties of Temperature, Rate of Strain, and Filler Content on the Tensile Yield Stress of nylon 6 Composites Filled with Ultrafine Particles,” Journal of Macromolecular Science, Part B: Physics, Vol. 22, No. 4, 1983, pp. 601-618. doi:10.1080/00222348308224779
P. Ayak, S. K. Sahoo, A. Behera, P. K. Nanda, P. L. Nayak and B. C. Guru, “Synthesis and Characterization of Soy Protin Isolate/MMT Nanocomposite Film for the Control Release of the Drug Ofloxacin,” World Journal of Nano Science and Engineering, Vol. 1, No. 2, 2011, pp. 27-36. doi:10.4236/wjnse.2011.12005
A. A. Aly, E.-S. B. Zeidan, A. A. Alshennawy, A. A. El-Masry and W. A. Wasel, “Friction and Wear of Polymer Composites Filled by Nano-Particles: A Review,” World Journal of Nano Science and Engineering, Vol. 2, No. 1, 2012, pp. 32-39.
M. C. Kuo, C. M. Tsai, J. C Huang and M. Chen, “Peek Composites Reinforced by Nano-Sized SiO2 and Al2O3 Particulates Materials,” Chemistry and Physics, Vol. 90, No. 1, 2005, pp. 185-195.
T. E. Attwood, P. C. Dawson, J. L. Freeman, L. R. J. Hoy, J. B. Rose and P. A. Staniland, “Synthesis and Properties of Polyaryletherketones,” Polymer, Vol. 22, No. 8, 1981, pp. 1096-1103. doi:10.1016/0032-3861(81)90299-8
P. K. Goyal, Y. S. Negi and A. N. Tiwari, “Preparation of High Performance Composites Based on Aluminum Nitride/Poly(Ether-Ether-Ketone) and Their Properties,” European Polymer Journal, Vol. 41, No. 9, 2005, pp. 2034-2044. doi:10.1016/j.eurpolymj.2005.04.009
P. Cassagnau, “Payne Effect and Shear Elasticity of Silica-Filled Polymers in Concentrated Solutions and in Molten State,” Polymer, Vol. 44, No. 8, 2003, pp. 2455-2462. doi:10.1016/S0032-3861(03)00094-6
Y. H. Lai, M. C. Kuo, J. C. Huang and M. Chen, “Thermomechanical Properties of Nanosilica Reinforced PEEK Composites,” Key Engineering Materials, Vol. 351, No. 15, 2007, pp. 15-20. doi:10.4028/www.scientific.net/KEM.351.15
Q. H. Wang, Q. J. Xue, W. M. Liu and J. M. Chen, “The Friction and Wear Characteristics of Nanometer SiC and Polytetrafluoroethylene Filled Polyetheretherketone,” Wear, Vol. 243, No. 1-2, 2000, pp. 140-146. doi:10.1016/S0043-1648(00)00432-4
C. J. Schwartz and S. Bahdur, “Studies on the Tribological Behavior and Transfer Film-Counterface Bond Strength for Polyphenylene Sulfide Filled with Nanoscale Alumina Particles,” Wear, Vol. 237, No. 2, 2000, pp. 261-273. doi:10.1016/S0043-1648(99)00345-2
E. Reynaud, C. Gauthier and J. Perez, “Nanophases in Polymers,” Revue De Metallurgie, Vol. 98, No. 1, 1999, pp. 169-176.
Q. H. Wang, Q. J. Xue and W. C. Shen, “The Friction and Wear Properties of Nanometre SiO2 Filled Polyetheretherketone,” Tribology International, Vol. 30, No. 3, 1997, pp.193-197. doi:10.1016/S0301-679X(96)00042-4
M. Q. Zhang, M. Z. Rong, S. L. Yu, B.Wetzel and K. Friedrich, “Improvement of Tribological Performance of Epoxy by the Addition of Irradiation Crafted Nano-Inorganic Particles,” Macromolecular Materials and Engineering, Vol. 287, No. 2, 2002, pp. 111-115. doi:10.1002/1439-2054(20020201)287:2 3.0.CO;2-I
F. Li, K. Hu and J. Li, “The Friction and Wear Characteristics of Nanometer ZnO Filled Polytetrafluoroethylene,” Wear, Vol. 249, No. 10-11, 2002, pp. 877-882. doi:10.1016/S0043-1648(01)00816-X
W. G. Sawyer, K. D. Freudenberg, P. Bhimaraj and L. S. Schadler, “A Study on the Friction and Wear Behavior of PTFE Filled with Alumina Nanoparticles,” Wear, Vol. 254, No. 5, 2003, pp. 573-580.
A. A. Ayman, E. B. Zeidan, A. M. Hamed and W. Y. Ali, “Effect of Heat Treatment on the Abrasion Resistance of Thermoplastic Polymers,” EGTRIB Journal of the Egyptian Society of Tribology, Vol. 7, No. 4, 2010, pp. 52-64.
A. Hoshino, K. Fujioka, T. Oku, S. Nakamura, M. Suga, Y. Yamaguchi, K. Suzuki and M. Yasuhara, “Quantum Dots Targeted to the Assigned Organelle in Living Cells,” Microbiology and Immunology, Vol. 48, No. 12, 2004, pp. 985-994.
Y. X. Zhou, F. Pervin, S. Jeelani and P. K. Mallik, “Improvement in Mechanical Properties of Carbon Fabric-Epoxy Composite Using Carbon Nanofibers,” Journal of Materials Processing Technology, Vol. 198, No. 1-3, 2008, pp. 445-453. doi:10.1016/j.jmatprotec.2007.07.028
A. L. Martínez-Hernández, C. Velasco-Santos and V. M. Casta?o, “Carbon Nanotubes Composites: Processing, Grafting and Mechanical and Thermal Properties,” Current Nanoscience, Vol. 6, No. 1, 2010, pp. 12-39. doi:10.2174/157341310790226270
D. Srivastava and C. Wei, “Nanomechanics of Carbon Nanotubes and Composites,” Applied Mechanics Reviews, Vol. 56, No. 2, 2003, p. 215. doi:10.1115/1.1538625
A. Plaseied and A. Fatemi, “Mechanical Properties and Deformation Behavior of a Carbon Nanofiber Polymer Composite Material,” Proceedings of MN 2006 Multifunctional Nanocomposites, Honolulu, 20-22 September 2006, pp. 203-208.
U. A. Joshi, P. Joshi, S. P. Harsha and S. C. Sharma, “Evaluation of the Mechanical Properties of Carbon Nanotube Based Composites by Finite Element Analysis,” International Journal of Engineering Science and Technology, Vol. 2, No. 5, 2010, pp 1098-1107.
B. Zhao, J. Wang, Z. J. Li, P. Liu, D. Chen and Y. F. Zhang, “Mechanical Strength Improvement of Polypropylene Threads Modified by PVA/CNT Composite Coatings,” Materials Letters, Vol. 62, No. 28, 2008, pp 4380-4382. doi:10.1016/j.matlet.2008.07.037