ArticlesArchiveAboutEditorial BoardAuthor Guidelines
Call for papersThe 2026 special issue on Climate & Health is open for submissions.Learn more
The Journal of Minerals and Materials Characterization and Engineering is an international peer-reviewed journal for the publication of original research in the fields of characterization of the minerals, metals and materials and its applications to the processing of them. Characterization has become the foundation fo…
Hoda S. El-Faramawy, Saeed N. Ghali, Mamdouh M. Eissa
This work aims at investigating the influence of titanium addition on behavior of medium carbon steel. Three types of medium carbon steel with different titanium content and one reference steel titanium free were produced in 100 kg induction furnace. Titanium…
Shweta Umale, Prakash Mahanwar
New naturally occurring mineral based pigment of general formula Hg 2 S have been processed and characterized for its application in surface coating. Various analytical protocol like XRD, FT-IR, SEM and CIE 1976 colour coordinate system have been performed fo…
Harshit Kumar Khandelwal, Kamal Sharma, Rahul Chhibber
A weld joint is composed of three principal zones viz., base metal, Heat Affected Zone (HAZ), and weld zone. Thus, the variation in mechanical behavior exists not only among these zones, but also from point to point in each individual zone. Being destructive…
Shouvik Ghosh, Prasanta Sahoo, Goutam Sutradhar
Aluminium metal matrix composite is a relatively new material that has proved its position in automobile, aerospace and other engineering design applications due to its wear resistance and substantial hardness. Need for improved tribological performance has l…
Jagjeet Kaur, Nemana Subramanyam Suryanarayana, Beena Jaykumar, Vikas Dubey, Ravi Shrivastava, Huma Nazli Baig
The present paper reports Thermoluminescence (TL) Glow curve of Mn 2+ doped CaAl 2 O 4 phosphor with different UV exposure time. The Glow peak shows general order kinetics and evaluation of kinetic parameters was done by peak shape method. Calculations of Tra…
Anand Kumar, Manas Mohan Mahapatra, Pradeep Kumar Jha
Addition of reinforcement such as TiC, SiC, Al 2 O 3 , TiO 2 , TiN, etc. to Aluminium matrix for enhancing the mechanical properties has been a well established fact. In-situ method of reinforcement of the Aluminium matrix with ceramic phase like Titanium Car…
S. Lincy Mary Ponmani, P. Selvarajan, N. Balasundari, D. Jencylin
A new organic single crystal of β-Alanine Oxalate (BAO) has been grown from solution by slow evaporation technique. Transparent, colourless crystals of size upto 11 × 9 × 4 mm3 were obtained. Formation of the new crystal has been confirmed by single crystal X…
Malkapuram Devaiah, Thodeti Srihari, Thankappan Pillai Rajasekharan
SiC particulates reinforced alumina matrix composites were fabricated using Directed Metal Oxidation (DIMOX) process. Continuous oxidation of an Al-Si-Mg-Zn alloy with different interlayers (dopents) as growth promoters, will encompasses the early heating of…
Satya Sai Srikant, Saroj Kumar Singh, Partha Sarathi Mukherjee, Raghupatruni Bhima Rao
This paper deals with the effect of microwave energy for mullite formation from placer sillimanite. A mullite formation is seen when 60 % SiC and 5% binder are used with the composite charge material, i.e. sillimanite (60%) and Al2O3 (40%). The maximum temper…
Ihom A. Paul, Suleiman U. Mohammed, Nyior G. Bem
The Impact of Swelling Indices of Sokoto Clays on the Moulding Properties of the Clays in Sand Mixtures was investi- gated. Four clays (labeled A, B, C, D) from different locations in Sokoto state of Nigeria were sampled. The sampling method was that for each…
No articles in this issue.
The Journal of Minerals and Materials Characterization and Engineering is an international peer-reviewed journal for the publication of original research in the fields of characterization of the minerals, metals and materials and its applications to the processing of them. Characterization has become the foundation fo… All articles are open access under a CC BY 4.0 licence, with authors retaining copyright.
Authors submit their manuscript, metadata, and declarations through the portal. There is no submission fee.
The editorial office screens the manuscript for scope, completeness, and formatting before assigning a handling editor.
At least two independent reviewers evaluate the manuscript under single-blind review. Where revisions are required, authors respond point by point.
On acceptance the article processing charge is invoiced and the CC BY 4.0 copyright handover is signed.
The article is copyedited, typeset, and given a DOI, then publishes open access with a permanent link.
Manuscripts must be original and not under consideration elsewhere. Submit in Microsoft Word or LaTeX with figures at 300 dpi minimum. Structure research articles as Abstract, Introduction, Methods, Results, Discussion, and References.
Use the journal's numbered (Vancouver) reference style. Cite sources consecutively in the order they appear, and ensure every reference is complete and retrievable.
Declare all funding sources, conflicts of interest, and ethical approvals (including informed consent and animal-care statements where applicable).